I recently purchased a used spinning wheel that came with a box of old yarn, and in that box was a long chained warp of 8/5 linen.  I'm getting ready to take a rug weaving class that requires a shorter warp of 8/5 linen, so I'd like to figure out the best way to unwind the old warp and reuse the linen for this project.  Other than a musty smell, it seems to be in good shape.  Any suggestions?

Comments

sally orgren

First, did you do a pull test on single strands of the warps in a few different places to make sure there wasn't weaknesses elsewhere along the length of the warps? (Rugs require high tension, so it would be a shame if, after all your work to rescue the warp, it starts breaking on you when weaving in class.)

Do you warp front-to-back, or back-to-front?

If there is still a cross in place, you can start by carefully placing lease sticks into the the cross. Secure the ends of the lease sticks (so the warp won't fall off) and walk the warp over to the loom. Affix the lease sticks near the castle, and begin sleying the reed/threading from the cross (for front-to-back), or add a raddle, spread the warps out to your desired sett in the raddle, secure the top of the raddle, and begin beaming (for back-to-front).

Since this warp has been chained a while, perhaps a long time, I would absolutely add weight to the warp bouts to keep them under steady tension when beaming. Something like 2 pounds per 1-3" bouts. You want the beamed warp to be "rock hard" when finished for a rug—not mushy. Linen can be springy/lively, so the "crank-n-yank" warp method may not be your best bet in this situation.

If there is no cross, that IS a big bummer! I would set up some quick clamps (clamped upside down, so the shaft is pointing directly up like a stick) on the edge of a table, with my lease sticks suspended in the clamps just a few inches off the table surface. Make sure the ends of the lease sticks are loosely tied so the warps cannot fall off. I would spread the warp as flat as possible on the table in front of me, and begin to re-create the cross by picking up one thread at a time and putting it into the lease sticks in alternating order.

If you have to create the cross in this manner, it is especially critical to beam under consistent weight/tension. The warps will want to tangle at the cross if not under consistent tension, and it could be even more frustrating for you at this stage if the warp keeps binding up when beaming.

I had a warp come to me two years ago in this shape. It WAS a tedious process, but not horrible. Listen to a good TV program or radio show and it will go fast.

Yes, there are short cuts if you are an experienced weaver. For instance, a front-to-back person may just sley to the reed right from the chain, and skip the lease sticks. But you need to be pretty confident in handling your warps and the properties of linen to know the pros and cons of short cuts. (BTW, you know linen is stronger when wet, right?)

Good luck—if you have any other questions, just ask and I am sure someone will chime in.

twoquinns

Sally,

Thanks for the reply and suggestions.  To answer your questions, yes, there is still a cross and even a counting chain.  I've tried pulling on it in several places and it doesn't break, so I feel like it's still strong enough.  I warp back to front. 

My problem is that I only need 2 to 2 1/2 yards of 72 ends, and this warp is 3 yards of 218 ends.  So I wondered if I should try to put it back on the warping board and unwind a bunch of it or what.

 

sally orgren

So it's not so much the length that you want to reduce, it's the width. And thankfully, it's a short warp at 3 yards. This will be easy-peasy!

Here's what I'd do: Lock all the cats, dogs, kids, and husbands out of the room. Lay the warp out, like on a table or bed. You will need to unchain it. Insert the lease sticks into the cross and spread it out a bit. Make sure you can see the cross clearly in the lease sticks, no tangles at that point.

Then I would take a second set of sticks or dowels, and slide the warps you do not need onto those sticks. Then go down and separate the warp throughout the chain into the segment you are going to beam, and the rest of the warp. (So yes, you'll need some extra choke ties.) 

For the warp you won't be using, you can add stings to secure the cross (so you can remove the temporary sticks) and then rechain it. Another option, I don't chain my warps, I just "fold" them into a plastic zip-lock bag, so I am not building in twist when chaining. You can label the bag with fiber content, how long of a warp, and how many remaining threads for future use. (While I was at it, I'd stick something in the bag that could help remove the musty smell, too.)

Does that make sense?

I'll bet you'll have your rug warp beamed in no time!

twoquinns

That all seems to make sense.  I'll give it a shot when I have plenty of time to work with it so I don't have to leave it laying out unattended.  Thanks so much.

sally orgren

I think you will be good-to-go!

In case anyone else wonders, you can certainly try putting the warp back on a warping board, but I don't think that is necessary. And the warp may actually be several bouts combined from the warping process, so it may not all fit on one peg once you try and spread the cross out. (In my mind, the flat surface is a better bet to see what is going on and separate out the part of the warp you want to use.)

 

twoquinns

Worked like a champ!  Thanks for the help.

Submitted by twoquinns on