Can anyone email me a copy of the assembly instrutions for a Harrisville Design 36" 4/6. I have had to totally disassemble my loom in case we had to bug out of here because of the wildfires?. ...........Steve.

Comments

Erica

It looks like they sell them rather inexpensively. I'm not sure this is the manual for your loom. If it's not hopefully you can find yours on the site easily.

Cheers,

Erica 

weave2 (not verified)

Hi,

I had to reassemble my 40" Harrisvile using their instruction manual that I purchased.  The manual was a nightmare to follow!  The parts aren't number and of course, the various parts aren't either.  I relied on other weavers to help me by posting pictures of their looms.

I still have the manual somewhere and my loom is together and weaving, but I will never take it apart again.  My sone and I spent days on it.

I hope you have a better experience and if you need help, please email.

Alaa

 

 

 

 

kerstinfroberg

Swedish weavers (of old) used to mark (number) their parts - presumably when disassembling. Ie the (say: right side of) breast beam itself would get the number (numeral) I; the place on the loom frame where that end (ie the right side of) of the breast beam went would also get the number (numeral) I. (The opposite side would get no mark at all.) The (say: right side of) warp beam would get the number (numeral) II; the (right side of) the loom frame where the warp beam goes would have the number (numeral) II - and so on.

It is easy to number the parts, if taking the time to think over which parts *need* numbers. As "tradition" allow us to make actual marks... I assume that it is "allowed" to make actua marks today, too - maybe using a sharpie pen is easier that finding (don't know the correct word, here - the metal stamps that make "I" shapes?) ?

Doing it this way means that the higher number (numeral) is where you have to start when assembling, but perhaps that is a small inconvenience, compared to have to find a very old "instruction manual"?

- maybe what I'm saying is assuming some kind of generality that does not exist in American looms. All Swedish looms (that I have seen) are built to the same principle - have you assembled one, you have assembled  them all (almost). The (admittedly few) Harrisvilles I have seen look like "good old Swedish looms" - so maybe the same principle would be useable?

weave2 (not verified)

Can it be done legally?  I have a manual somewhere, but am unsure of whether it can be shared since it has to be purchased.  If it doesn't violate copywrite laws, I could look for it to send.

Alaa 

steve104c (not verified)

Weave2. I just checked out the copy right law. Can't make a copy for me. Thanks anyway................ Steve

Neshobe (not verified)

Harrisville should be ok to put together w/o manual. I put together a loom (LeClerc) by laying out the parts as they seemed to relate to each other and then figuring out which things had to be joined first. It wasn't too much of a hassle, Just took a little time and thought (and a helper). I had to make a run to the hardware store for some missing bolts and nuts.

Pretty hard to stop and think about numbering when you are trying to outrun a wildfire (or a flood- on my mind because we just had an ugly one here in Vermont). But now, as you re-assemble, might be a good time to do that (use bits of masking tape so you can change them if necessary-- you can do permanent marker or something later).

 

One thing I always do when dismantling things if I can, is to put bolts, nuts, screws, etc, in little bags and tape securely to the piece they belong to. Saves a lot of headaches later.

 

Good luck.

steve104c (not verified)

I did take a lot of pics. And when I brought it home, I replaced a lot of nuts and bolts and wing nuts. From what everyone is saying, the instuction book is not that good, so I'll just use my pics. Thanks to everyone for the replies....................Steve.

Michael White

The whole key to putting a loom together is having a good working knowledge of how a loom works. With your pictures you should have no trouble,

Michael

steve104c (not verified)

Michael, Have you guys gotten any rain? We got about a 1/2" today. Still 23" behind but needed to see what rain looked like. It brought back memories....................Steve.

debmcclintock

Hey Steve, over in Johnson City, Tx we got 1.1 inches of rain in 1/2 hour along with pea sized hail. It felt & sounded good. It was too fast for our cistern to catch (lots of gutter runoff) but we'll take it anyway!
Submitted by Anonymous (not verified) on