I am a life-long F2B warper, but I am self taught, and I recognize that B2F will, in the long run, be much more efficient.

I managed to put on a small warp, mostly following the youtube from WEBS: http://www.youtube.com/watch?v=icw_E0rHYBw

I put on a solid color warp, and put the loops of the end of the warp through the warp beam's tie-on rod. 

What I do not understand is how you warp with either an odd number of threads (so that not all have a loop at the warp beam end), and related, how you put on a striped warp.  I figure I could just do everything with even numbers of threads, but that seems an unnecessary limitation!  Thanks!

Comments

Sara von Tresckow

For a striped warp, you work with 2 threads on the mill or board and break and tie when changes are needed.

To avoid single threads, make a second cross. Make sure that your warp ends on the same cross as you started (even if this means having an extra warp thread). When you take the cross at the other end of the chain, you have all loops.

Otherwise, if there is a single thread, make it so that it has an initial loop large enough to slip over the tieon rod. And don't forter to attach it - if you forget the loop, just tie it to the rod before beaming.

kerstinfroberg

What I do, in the Swedish tradition, is first see if the odd numbers desired are divisible by something easy to manage, say 3 (5 is harder to hold in one hand, but it can work, too). If so, I wind until all ends are there, then tie a loop at the end I am. I'm using a mill, but I'm sure it is possible on aboard, too?

If not, or if you for some reason wind with only one end, I do the same: tie a loop (big enough for the back apron rod) at the "other" end (or should that be the "end end"? :-)

And ... voilá, done.

I do the same for stripes. Myself, I rarely wind with less than 4 ends. I tie on new colours whenever they are needed, trying to get the knot as near as the turning point as possible - the first and last few inches fall in the thrum area anyway. And yes (don't tell anyone else, in case there is a weaving police about...) - I do sometimes tie the whole bunch (4 ends) to the next bunch (that does not *need* to be 4 - can be 3, or 2, depending on colour sequence and availability of cones/spools) with just the one knot, usually an overhand knot.

Maybe I should add I have not watched the video. What I do is just what I was taught some 35 yrs ago, and I still think I get good results...

Have fun!

Kerstin in Sweden, who has never dared try F2B ;-)

 

Queezle

Tying a loop - of course - obvious now in hind sight, and thanks.

I use a warping board, and find measuring the warp the least enjoyable part of the whole processes.  But I've never tried holding more than one thread at a time.  How do you manage?  at the cross, do you place them in a special order?  I'd be afraid of making a mess! 

ReedGuy

Knotting ends

If I mill 2 ends at a time I just loop the ends as if one thread and make a knot. You'll find it prevents some very minor confusion (been there) when you have made your bout and putting it on the loom. The confusion is that you'll think you dropped an end at the lease because one end rides over and one end under when a loop is made with the end knotted instead of looping and knotting a couple inches from the end as shown. It won't hurt anything, but make you scratch your head. :) The loop is obviously for attaching to the tie-rod.  I  knot the same way with 3 or 4 ends. I only do up to 4 ends at a time. Any knots at the end of the warp end are obvioulsy trimmed once the end is cut in two for threading the heddles. The second knot and loop that is pictured is if I only need one of two ends, I separate the two leaving a long tail to make a loop for the tie-on rod and the other end is waste. With fine yarn I often just thread the waste end on the same shaft as the single that was needed, so I don't cut it off, just becomes part of the warp. If you are using the cloth to make garments your doing a lot of cutting and the selvedges will often not matter. But with fine thread 16/2, 10/2, 8/2 cotton an extra end at the edge isn't going to be seen. Just makes the edge stronger anyway.

Lease Cross on loom

These knots occured on the cross end because I was using up small amounts of yarn I had on multiple spools from other projects, in a sample piece. So sometimes instead of making the return trip back to the beginning turn dowel, I may only have yarn for half the trip and have to tie off, then tie on at the same place to continue on. This helps keep my count straight in my mind. This piece is a narrow sample and barely touched the warp roller so I just spread the ends as I thread the headles in groups of 16 ends, 2 ends per heddle in this piece. I usually use a couple Texsov cords looped with an arrow pin, one cord on each end of one lease stick (the one closest to the tie-on), to support the lease sticks as I add my bouts to the loom. My tie-on rod hangs over the back beam on the side facing to the front of the loom. Once I have the warp all on, the lease sticks tied at the ends (through the holes) with some twine and spread in the raddle, I wind the tie-rod over the back beam and support the lease sticks with the same texsolv cord as earlier, allowing the sticks to hang over the back now. So the cords are now looped over the other lease stick for this purpose. When winding and tensioning the warp, it looks like a sheet of cloth, under tension, being wound and packed with warp sticks. :)

kerstinfroberg

Holding all yarns separate, between the fingers, is the short answer. Since I have 5 fingers, there are 4 spaces - one end/space...

This is how I hold them. More on my blog, here. (oops, can't find the photo, but it is in the blog post, second pic)

And no, I seldom place them in order - I make the cross with whatever number of ends I am warping with. If you look at all the "warping" posts on my blog, there are discussions on the exact order, too. I guess one reason is that I am lazy, but another is that I like to warp with different nuances to make the cloth more "lively". (I'd never survive weaving with, say, four "random" wefts - imagine using 4 shuttles - but warping that way is both faster and... faster - I use a single shuttle for weaving.)

(And, actually, when going down in thread size, having more than one end in the cross makes for easier beaming)

 

http://oddweavings.blogspot.se/search/label/warping

kerstinfroberg

Why do you make a "going-back-on-itself" loop when you already have two ends? Two ends tied together make a space ("loop") to put around the apron rod, yes?

ReedGuy

Hi Kerstin,

It just makes confusion for me to just knot at the end of the yarn ends. When you are winding the ends they are kept together as you pass over the turning dowels to return. So when you separate the ends at the start when putting the ends onto the mill, with one thread over the top and the other under the turn dowel, it makes me think I have dropped an end when I slip the bout onto the tie- rod. And drives me nuts. LOL :D

sally orgren

I wish you lived close by! We just did a warp demo at our guild today, B2F, winding two warps at a time. Actually, warping with more than one thread is at least 2X faster so why not? If I am using a single color of warp, I might make a second "package" (or ball of center-pull yarn), so I can wind two stands at the same time. 

When it comes to stripes (and even stripes that contain an odd number of warps) I just end the color stripe where I need it, top peg (if an even count of warps in the stripe) or bottom peg for an odd number.

As for the cross, something else we talked about today... You don't always have to wind a 1:1 cross. You can carry two warps together through the cross down the warp board, then carry them together through the cross on the way up. You would describe this as a 2:2 cross.

If you want to wind with more than 4 threads at a time, you can warp with a paddle. The trick to using a paddle is that you have to manipulate the paddle warps through the cross, usually with your fingers. 

ReedGuy

I have a paddle and have used it to wind really fine polyester thread (like sewing thread). If I was doing a really long warp, I would use one for an 8 thread cross, maybe even 12.

Michael White

You can lay in your strips in order on just get them close and pick up the yarn you want when dressing your loom. You just don't want them so far apart that you get large cross overs which could cause problems. To answer a other question with practice you can make a warp of different types and kinds of yarns. Everything cones with practice.

 

pammersw

Ooo, that last one in blues and greens is gorgeous! 

Queezle

Thank you all so much!  I will certainly try making some balls of yarn so I can wind on the warp 2 or more at a time.  And that paddle looks like a good investment.  I won't have time to put on a new warp till the weekend, and I bet I come up with a few more naive questions... 

And Sally - I wish I lived closer, too!  But you are all such good weaving teachers -- even putting on pictures that illustrate the principles -- I bet I can now figure this out.  Many heart-felt thanks.

Kelly Range

I use a warp paddle for 8 ends (4 black and 4 white, colors of your choosing) for houndstooth scarfs. The cross is 8 ends, which works for me beaming front to back. Lots of saved time, plus no excess knotting at the non-cross end. As long as it works for you and comes out correct, Do It!

caloosa (not verified)

When winding holding multiple threads if you go around the top peg in clockwise fashion and the bottom peg in anti clockwise fashion the threads will not twist around themselves - making a difficult warp (ask me how I know) if you go in the same clockwise direction around each peg. 

When this one was explained to me felt like they were sharing "secrets of the universe".

Queezle

I guess I can remember this by recalling the coriolis effect!  I am really good at mucking up a warp, so tidbits like this are invaluable.

sally orgren

If you are warping with two colors, keep a finger between them to separate them.

Note which color is always closest to the warp frame. Then just keep the two colors traveling the warp board in the same way! 

Keep them parallel to the warp board when winding, and use both hands. Instead of turning your wrist as you take them through the cross or around the last peg or top peg, switch hands to maintain their relationship to the warp board. 

ReedGuy

Yes, as to warp winding on a mill. If you remember to always go over the top of the turn dowels, you will not get a twist. Your palm will go from face up to face down or vise versa. This is easiest on a mill because it swings, so you can do it with one hand and not have to shift. When winding multiple colors it keeps the order and no twist that would make it difficult to place on the tie-rod for starters and for me it keeps order when warping and no crossing at the lease. I hate chaos. :D

Submitted by Queezle on