I am thinking about winding warp on the loom by my self. My husband has helped in the past but I would like to learn to do it my self. Does anyone do it alone? Any ideas and advice would help. Thanks

Comments

Joanne Hall

Hi Laurie,

I think that most weavers do this alone.  I find that the best way is to put the bouts on the floor in front of the loom.  Put a towel under the warp and a weight on top.  I use bricks covered with cloth.  They will move on the floor as you wind on.  I describe this in my new book, Learning to Warp your Loom.

[email protected]

EvaHall

I have done that a lot. When I first started weaving my husband was often busy, and he looked tired whenever I brought the question of winding warp up. So I found in a book, I do not rememder which, a recommendation for difficult warps, like linen for instance, to wind one round at a time, then tighten the warp in sections acros the whole  width. I started on that with 20 meters of rug warp, which was hard on the hands, but very efficient.

These days I am planning a new rug warp, this time only 10 meters, and I am going to make myself a valet like the one Kerstin Froberg showed earlier on in weavolution.

http://weavolution.com/forum/weaving/warping-trapeze-16811

Joanne Hall

Hi Eva,

I used to tighten with my hand as well.  It is shown in Peter Collingwood's book.  But I too found it very hard on my hands.  So, using weights was the next step.  And yes, the Valet is a good solution if you don't have much space in front of your loom.  I turn my looms to a good position for having floor space in front of the loom and then the bricks on the floor are a very easy solution.

Joanne

laurafry

I *love* my warping valet!  It's especially good for long warps, wider warps, or warps that are not terribly co-operative.  :)  Shorter, narrower warps I can usually hold in one hand while I wind on with the other, but that only works for looms that are small enough to allow that.

cheers,

Laura

who uses water filled jugs for weight but anything heavy will do

r1mein54 (not verified)

So far for my few projects, I have tied my warp to a sturdy wood chair and added large books & phone book in the seat for weight. As I crank and wind, the warp is pulling the chair toward the loom.

sequel (not verified)

I don't have room for either valet or trapeze.  I weight approx. 2" bouts of warp near the floor in front of the breast beam.  I shake out the slack, make a slip knot and hang a 1 lb. weight from the knot (I use knitting machine weights or 1 lb. lead fishing weights with an S-hook.)  Then I crank on until the weights begin to touch the breast beam.  Move the weights, and start again.  Don't let the weights sit on the floor, don't work groups in the same order each time, and every now and then, like maybe every 3 times, "yank" (continuous downward pressure) the groups to tighten on the warp beam.

This technique eliminates the problem of the "triangle" you get when trying to weight the whole warp with only one weight or one helper.  The edges are under the about same tension as the center.

You may start and stop a lot, but you'll do that anyway to check for threads hanging up on the raddle...

Sara von Tresckow

You don't need a valet - every loom has crossbeams that allow warp chains to wrap around them. Andreas Moeller, a y oung German weavers has even come up with a way to add some cross members for warping.

The chains are then wrapped around the cross members - much the same way as one threads a tension box for sectional warping - each wrap adds tension to the warp as it passes over. This concept is pictured in several weaving books from Europe, including Ulla Cyrus-Zetterstrom's "Manual of Swedish Weaving" where the warp winds over several beams on the loom and two young girls sit under the loom holding the tension.

This way takes up NO additional space in your studio and is just as effective as the valet.

freitagcarolyn (not verified)

I recently got a LeClerc Nilart 12 harness and realized it would be best to warp back to front.  Unfortunately I have only done front to back.  Are there any good DVD's that might be able to help?

caloosa (not verified)

Peggy Osterkamp has 4 GREAT books for weaving and warping that I have and can reccomend.  She has a DVD that I have not seen - but would assume would be helpful based on her books.

weave2 (not verified)

tie the wrap the warp around the front beam and loosen it in small increments as I wind on the back.  I also comb the warp in between and keep the choke ties in as I do.

I also grab it sometimes, and give it a tug.

 

mneligh

I always warp alone.  It's the only way I know to guarantee that the tension is consistent.

On my smaller loom I use weights (filled jugs -- I know they can burst) on each of about 4 sections as I reel on the warp front to back through both the reed and heddles.  The back beam comes off, so it appears it was intended to be threaded that way.  On my my Macomber, though, the front beam folds down for threading and I sit inside the loom for threading.  On that loom I use either conventional or my own variant on sectional warping, the latter being from a chained warp.  On that one I thread after warping.

Unless there is some mechanical reason (like folding the loom) not to use a sectional beam, I don't know why everyone doesn't use them.  They are easily made, and don't necessarily require one to have a spool rack and tension box, although the tension box helps.  One other big benefit is that on a long warp with a conventional beam, even placing newspapers between the layers, I've had problems with the edge warp threads slipping sideways off the bulk of the rolled warp, thereby loosening tension.  I've taken to putting lathe strips in every vew layers to ease this.  Of course, I fold and move that loom a lot.

I also hand-tighten when finally tying-on, and on linen I end up with blistered or bloody hands on my big loom.  Gloves are not sensitive enough, but taping the hands beforehand helps.  I don't double knot until I've "debugged" the threading, and woven a couple of inches with really large, soft stuff like rolled newspaper.  I then let it sit over night before finally double-knotting.

Sara von Tresckow

There is no need for bloody fingers tying on. Learn to achieve even, moderate tension and then use the ratchet on the loom to get the last little bit.

Submitted by Anonymous (not verified) on