I was recently showm how to lash/lace on. I had previously used the weaver's knot. I also saw on one of the Facebook group a way of tieing on by taking one half of the bundle over the bar and one half under, but can't remember how exactly that method was tied. I think someone mentioned this was taught at one of the schools in Sweden. But of course, since this was posted on Facebook, I have no way of searching for it now. This is why I'm not really a fan of the Facebook groups, but fortunately we have the vast amount of knowledge here! I would appreciate it if someone can enlighten us on this method.

I am also interested in hearing what method you use, and why you like it!

Comments

jmbennett (not verified)

Dress Your Loom the Swedish Way Becky Ashendon dvd, Big Book of Weaving, Learning to Warp Your Loom Joanne Hall.  All great sources.  And I love winding a warp and warping my looms.

Erica J

Thanks jmbeennett,

T hese are great resources for new weavers. I am hooing to generate some discussion on what people do and why they prefer the methid they have chosen.

I like both tye weavers knot and lacing on. Both are easy to tension in my experience. Lacing on is great when you really want to minimize waste, for example on silk warpa that will be hemmed.

What do you do and why do you like it?

Artistry

Erica,

once I discovered lashing I never looked back! It's fast , efficient and accurate. The key , IMO, is to keep the bouts on the smaller side, not big fat wads, this will help with the even tension.

i choose this method over tying on because it's faster for me:)

Erica J

Thanks Shawn that was the method I had seen!

ShawnC

You're welcome, Erica. I haven't tried this yet, but it seems like it should be quite nice.

 

jmbennett (not verified)

several ways since for some reason this was the hardest part of dressing the loom for me to understand.  I tried shoelaces and lashing/lacing and both were a mess.  Kept with the Swedish method and finally relaxed enough to make it work.  Once I relaxed, it became a piece of cake.    

sally orgren

I started with bouts: tightening the center bout, cranking up the tension one unit, then tightening the next two outlying bouts, cranking up the tension one unit, tightening..., etc., in the hopes that when I was done, it would all be perfectly even.

 

I found no matter how careful I was, I still had to play "pat the bunny" across the warp, and I wasn't confident I could accurately "feel" if my warp was evenly-tensioned, especially over 45" width, and especially when you are a new weaver, and maybe haven't felt a lot of warps before to know. (Of course, you always seem to find out after weaving about a yard or so it wasn't as perfectly tensioned as you thought! ;-)

 

When I discovered lashing, I never looked back. It's like the slippery lashing cord seems to magically adjust the tension over the whole warp width – the knots seem to slide into place automatically with some shuttle-less treadling before you actually start weaving. And I went from 10-12" loom waste at the front, to as little as 3".

 

The one point detractors have about lashing: if you discover an error once you start weaving, then you have to unlash all the bouts and lose all your perfect tension. Not so – I discovered a workaround!

 

 

I isolate the bout that contains the threading error. I use spring-type clothes pins to affix the lashing cord securely to the bar/rod on either side of the isolated bout. Then I remove some of the tension from the warp (just enough to go slightly slack). The clothespins allow me to unknot the bout in question and make the correction, while keeping the lashing cord exactly where it was on everything else. (I use a third clothespin to hold the part of the bout I am not working with out of my way.)

 

 

When the correction is complete, I can just divide that isolated bout into two halves, and reknot over the loop of the lashing cord (which is held suspended in place by the clothespins), matching the rest of the warp.

 

 

When done, I remove the clothespins and I crank back up the tension. Most times it is perfect, but if not, it is very easy to make minor adjustments to the slippery lashing cord by treadling a few passes again (without weft) to get everything to slide back into place! (In the past, I could never seem to get the isolated bout to match the tension of the rest of the warp bouts, so I ended up retensioning all the bouts, generating even more loom waste at the front of the loom – Oy!)

 

Also with lashing – once tensioned, throw 3 angled pics of your weft without beating between each throw. THEN, pull the reed forward to compress the weft(s) into place all at once. If there are any inconsistencies in your warp, they will be pulled to the front with this step, and you will have a perfectly tensioned warp in far less time than all that bout-tying and patting takes.

Guiding Myth (not verified)

Hi,

Sally, that is a wonderful method.  Thanks for explaining it, I'm sure I will use it. Sometimes I manage to misthread several threads.  

When I find an error and it's only one or two threads I cut the thread close to the knot (the knot holding the group of warp threads being lashed on) to rethread it.  When I'm finished I hang a weight on it. After 5 - 8 inches of weaving I don't need the weight anymore.  

So to answer Erica's question - I lash on. Much easier and faster for me.

Stephanie S 

Erica J

It never occured to me that fixinf a threading error would me taking the lacing cord out. I have just untie the bout of threads, fixed the error and split it u o again an retied behind the cord. I like your method too, Sally!

Artistry

Leave it to Sally to figure out how to detach the bout and put it back again without creating a mess! That is one comment I have definitely bookmarked for future reference!

laurafry

I use one of two methods...usually I tie on with the surgeons knot.  I don't ever 'pat' the warp to see if the warp is evenly tensioned.  Rather I lightly run my hand from one side to the other so that I can feel the tension with my whole hand and more easily feel where there are looser or tighter areas.  my bouts are about one inch 

if I'm working with a slippery yarn I lash on. 

I show both on my DVD if I remember correctly. 

Cheers

laura

endorph

lashing on amost exclusively. I find it much easier to get an even tension this way. And I will add my thanks to Sally for a great tip on fixing threading mistakes when lashing on. Brilliant and so simple!

Joanne Hall

Thanks Shawn for sending this link for the Swedish method.  I switched to using this method about 20 years ago and never looked back.  It really is the easiest and fastest method.

Joanne

Joanne Hall

One thing that I learned 35 years ago from Anita Mayer, is to tie a very small bundle of warp threads at the selvages.  This will reduce the draw-in you experience with your first wefts.

The second is for adjusting the tension after you have tied up all the warp.  I take one finger and touch the warp from one tie, about two inches above the tie.  This gives me an instant report on the success of the tie-up of that individual tie.  I feel five or six in a row and that tells me if one of them needs adjusting.

The third is one that has saved my hands, especially with wide warps, as well as linen or non-stretchy warps.   I do not tie the tension very tightly, but instead, moderatly tight, looser than when I am weaving.  I want each to be the same tension.  I can tighten them with the ratchet when I am finished.  When I need to make an adjustment, I find the tightest tie and I untie and loosen it.  I only tighten a tie tighter if it is the only one that is too loose.  This will save you hands and it will save time as well.

ShawnC

She made it look so painless-and intuitive. I'm trying it on the next warp!

kerstinfroberg

Personally, I would take off the outer apron cords for such a narrow warp - leaving them all on will (over time) make the rods bow.

(This goes also for the back apron cords)

Submitted by Erica J on