I'm in the middle of fixing my threading/sleying mess for the umpteenth time.  I've learned one thing:  NEVER dress your loom at the end of a work day with a glass of wine at your side.  PLEASE...I need to laugh about this before I tear out my hair as well as the fiber!  Tell me your horror stories...happy endings welcome.

Comments

naturalfibres (not verified)

I'm trying really hard to think of a threading nightmare, but I can't think of one - I'm sure that I've had them, but obviously I've blocked them out!!

 

debmcclintock

Ma'am, put the scissors down and walk away from the loom!

tien (not verified)

OK, I have one...Just three days ago I was humming along, treadling the threading (which, on a computer driven loom, allows the computer to manage which heddles should be threaded next).  As I neared the end, I suddenly realized that I had been threading off an incorrect file.  Genius that I am, I managed to thread 720 threads of an ENTIRELY WRONG THREADING!!!

I believe people now when they say that computers are the fastest way to make mistakes, short of handguns and tequila.  Except this wasn't a particularly fast mistake, since it took me three hours to finish making it!

Fortunately, after I had finished saying bad words and had walked away from the loom for awhile, I had no trouble rethreading it with the RIGHT pattern.  It took me a couple of hours to correct, but I rethreaded flawlessly and am happily weaving!

And here is the sparkly proof:

Just goes to show, all's well that ends well!  I'm sure you'll get your error corrected in no time, and be back to weaving shortly.  :-)

Threshkin (not verified)

I volunteer to demonstrate weaving at the National Western Stock Show in Denver CO.  I have done this several times and always had a great time showing the kids how to weave.

Last year when I arrived I discovered that the warp had been wound on with out anything between the layers and was a tangled, uneven mess that was completely unusable.  The show was going to open in 1/2 hour and I had to re-wind this warp FAST.  But how was I going to do it?  I was far from my studio and had no packing paper or sticks.

I started running through the vendor booths looking for anything I could use but most were closed or only just opening up.  I couldn't go into an unoccupied booth for fear of being accused of stealing.  Time was running out what was I going to do?

I ran outside (in the rain) to check the food vendors and found what I needed!  Chopsticks!!!!  I quickly asked the vendor if I could have a large handful and then had to explain why.  After breathlessly trying to explain why I needed them (in the rain) using terms I am sure he did not understand at all i was given permission to take all I needed.

Clutching my treasured chopsticks I ran back upstairs (2 long flights) to my booth.  I ripped the wrapping off the first set of chopsticks and discovered......They were too short! 

No worries I will just use two at a time.  No problem, right?

Picture the scene - The show is now open, I am in an exposed location with kids and parents milling around asking questions about what I am doing.  I have no place to lay out the warp without it getting trampled so I effectively have to re-beam it twice.  First I wind it on to the cloth beam adding pairs of chopsticks frequently to start evening out the tension. Then I retie the warp beam to take out the worst of the unevenness (this warp was BAD).  Finally I re-beam the warp, carefully managing the tension and inserting pairs of chopsticks frequently to keep the it even.  Try maintaining warp tension, adding pairs of too short warp sticks, winding the warp and explaining what I am doing to groups of 8 year olds all at the same time.  Finally I retie the front beam and breath a sigh of relief.  I am exhausted, wet (remember the rain?)  and I haven't even started the demo yet!

After all that did I ever come back?  Of course!  I love teaching kids how to weave.  I was back the following weekend (no warp problems thank heaven!) and again this year.  I cannot imaging not sharing the joyful rhythm of treadle, throw, and beat!

Claudia Segal (not verified)

Oh, I love this thread.  My threading nightmare came when I was in my second year of weaving and had taken a weekend long class with Tom Kniseley at the Mannings (PA) and came home determined to make a shawl exactly as we had done over the weekend.  (Just an aside, I chose a wool/mohair for warp in the class and had to clear each shed with a sword for every pick to weave 85" of a 24 ppi shawl).

Back home, after the class, I wound the 580 ends of a new warp using 10/2 cotton I had purchased 4 months prior from another handweaver.  I had my cheat sheets with me and was all set to start warping front-to-back for the first time all by myself.  I set up at my Baby Wolf (26" wide) and began sleying the reed.  The shawl had a supplementary warp in a turned Monk's Belt pattern.  I started with sleying the reed at the loom and had a feeling things were going to be tough when it occured to me that my weaving width was exactly the same as my project.  So, undaunted, I moved to my 45" TOTT loom and got resettled.  The pattern called for 4 shafts and I had moved to 8 shafts so I decided to alter the pattern to use all 8 shafts with the ground warp (3 shades of gray and 1 black) on shafts 1-6 and the supplementary warp on 7 & 8.  All is good until I sley the reed, thread the heddles and realize I had not maintained my cross.  Nothing to solve that until I get it tied on.  So, I bring the threads through the heddles and tie on to the back apron rod.  A friend is helping with the beaming process and as I begin to wind on, the black warp threads start to pop!  Of course, I have wound on about 6" now and I have a tangled mess with no cross at the front of the loom and bunches of black threads popping like popping corn in a microwave.  I could do nothing but stand, paralized and stare at the warp.  It was a total nightmare.  

Eventually I was able to warp the loom and finish the shawl but we had to handle the black threads like fragile eggs.  Wind an inch or less and check they were all there.  I ended up replacing/repairing about 50 warp threads and finished the shawl but was convinced I would never warp f2b again.  And I learned a valuable lesson about checking the strength of a yarn before using it.  And about black yarn.  Here's a pic of the shawl which you can also see here.  

Claudia

illoominated (not verified)

Your stories made me gasp and laugh out loud.  OK, I'll try again today with a cup of tea next to me.  Perhaps, chamomile.  

And all your happy endings are lovely!

Thanks, Jane  

loomyladi (not verified)

4 years ago, I wound a warp and commenced to weave, and quickly realized that there was a problem with Harness 3 & 4, they were not dropping back down, (jack loom), I noticed that the harnesses rose at an angle.  Well, life got in the way and the loom sat and sat, and then I moved. Periodically I would sit at the loom and try to figure out why the harnesses were not moving correctly.  At the new place weaving friends came and went, often times stopping at the loom which was sitting warped inside the front door.  We could not figure out the issue.  Finally, fully frustrated and aggrevated I persuaded my loom guru to come "visit".  I figured that with his 20 years of loom experience if the problem was solvable, he could do it.  Well, 3 hours later we decided that the castle had warped and that the application of pressure was needed to pull the wood back in.  So ratchet strap was used and there was improvement.  The harnes raised, most of the time, and if you jiggled the loom it would fall. 

3 other weaving friends all with 20 plus years of experience sat at the loom, tweaked, contemplated, and threw their hands up in despair.  I made up my mind that the loom was in complete mechanical failure and would have to go to the bone pile.  Then I had an idea, if the ratchet strap helped perhaps there was just not enough tension to hold the wood in.

A woodworking friend used some add a clamps onto a LONG piece of heavy pipe.  My thinking was, if the constant pressure of the clamp fixed the problem I could invest in a permanent wood "clamp" to hold everything in place. 

So two days ago, I affix the clamp, and there is improvement, but the #4 harness STILL sticks at the top and is raising at a slight angle. 

Then, the lightbulb goes on!  Four years ago when I warped the loom, I was not as proficient in loom dynamics as I should have been so I moved all of the unused metal heddles to ONE SIDE of the harness.  Of course the harness will not raise straight when there are 200 wire heddles on one side only!

I have had a good laugh with my weaving friends and as they collectively have more than 150 years of weaving experience and none of them noticied the unbalanced harness I feel not quite so stupid.

The happy ending, the harnesses are now all balanced and I have it about 1/2 way rewarped.  So after more than 4 years of sitting and taking up space it is once again earning its keep.  YEAH!!!!

weaver1126

My horror story involves some small kittens that my step children let into the house without me knowing.  Need I say more.  I had to throw it away.

celtinbirks

Hi!

Ever see a Peanuts cartoon of Charlie Brown wrapped in kite string???  That's me!

Candace

Vicki Allen (not verified)

I once saw the most beautiful weave... I set it up on my counterbalance loom and began to weave. It was blue and white but it did not look like the picture. Lo, I had threaded it upside down. So the pattern I wanted to watch as it formed was on the bottom! I finished the piece and enjoyed it.

Later I decided to weave another piece using the same pattern. This time I carefully threaded it differently so the pattern would be on top. However, I wanted a larger piece so this time I put it on my jack loom.

Guess what! The pattern was still on the bottom since the counterbalance shafts sink and the jack shafts rise.

The joke was on me!

It is still  my favorite weaving pattern, though.

Vicki Allen

Amelia Garripoli (not verified)

I was happily warping my rigid heddle, got the threading all the way across fairly quickly, then turned the loom a 1/4 turn to tie on to the front ... and had the heddle fall off and too the floor. Completely fell off the warp. Ouch. No cross to recover from, just all those warp ends waving. Attracted the cat, who came over and helped reorganize them.

Once I recovered from that (I forget if I felt faint, nauseous, or what -- but I remember taking recovery time!) I sat down with the loom and calmly threaded across the heddle as close to the order of threads in the wound warp as I could figure out.

Luckily rigid heddle looms are forgiving, there were only 2-3 egregious misthreadings that I discovered at the end of the warp, but the fabric wove off as well as an undropped warp. Whew!

Submitted by Anonymous (not verified) on