HI y'all,

Awhile back I posted about scoring a Macomber and an oak Herald loom plus a huge stash of yarn through Craig's list.   I've been happily weaving on the small Macomber loom, and we just recently moved the larger Herald loom into the house.  After cleaning it, it looks like the heddles have rust and nastiness on them and there are only heddles on 4 of the 8 shafts.  I am thinking about replacing them with texsolv heddles......is there any reason this won't work?

I used a table loom with texsolv heddles when I took weaving classes and liked them fine, especially the quiet.  

Would I just measure the metal heddles and order texsolv the same length?

Today my granddaughter is weaving mug rugs for Christmas gifts on the CP11 Macomber loom, it is the perfect size for an 8 yr old.  She's turning into quite the little weaver - but as I told my daughter-in-law; I have to have SOMEBODY to leave all these spinning wheels, looms and knitting equipment!

Thanks in advance!

Deb in N TX

Comments

Alison (not verified)

I hope someone who has actually made the change to this type of loom writes. 

The only idea I have to contribute is to that you should check if the shaft frames are heavy enough with few heddles to go down properly after treadling them.  When I bought my baby wolf, the back shafts had few  heddles and they wouldn't go back down properly.  The problem went away when I added heddles. 

I had considered going to Texsolve but was warned that I would need to weight the shaft frames if I did.

Su Butler

Jack loom usually have metal heddles because the weight is needed to both return the shafts to their resting position after raising them AND to keep the shaft from floating due to tension appllied to the warp.  I used to weave on Herald looms in college, and they performed quite well, but all had flat steel heddles, so they had considerable weight.  While you *could* put Texsolv heddles on this loom, I think you might run into floating shaft issues, so the question would be is the somehwat reduced noise level you might gain (a shaft left to slam down on it's own will be loud whether there are metal heddles on it or not), is worth the trading for the problems that might arise with shafts that are too light to behave as designed.  

If you allow the shafts to bang down, any heddles will not quiet the loom down, but if you lower the shafts by releasing the pressure from the treadles slowly, they will not bang down into position.   Since the loom was designed to use the weight of the heddles, my advice would be to add flat steel or inserted eye heddles to the loom. 

Su

debstein (not verified)

Thanks so much - I believe you are right.  I tied up one of the shafts without heddles  to a treadle and it didn't want to come down by itself - I guess it just seemed to me that the oak shafts would be heavy enough that the heddles wouldn't make that much of a difference, but I was wrong.  So I guess I will try to salvage the heddles I can and order flat steel ones for the replacements.

 

Deb in N  TX

sequel (not verified)

Flat steel heddles can be cleaned with 0000 steel wool (and maybe a little WD-40).  You'll have to be very careful not to bend them.  Chances are, you have some rust or white-ish corrosion .  You may have to ditch any heddles with corrosion on the heddles eyes, unless you can be sure they are really smooth.

My first loom had rusty heddles and I cleaned every one of the 600-800 heddles this way because I was too poor to buy new ones. 

On your Herald, You may want to check your "cushion" where the harnesses sit at rest.  Herald used a rubber pad that disintegrates into a sort of black glue-y mess that can actually stick the harnesses down.  Yours may be okay, sticky or just plain gone... you can substitute a strip of that stick-on heavy felt you buy at the hardware store for furniture glides and the bottom of lamps and such.

Good luck, and I hope you enjoy your Herald as much as I enjoy mine!

 

 

 

mrdubyah (not verified)

I've had very good luck with what we call a "greenie"; a green 3M scouring pad.  You can get them in the cleaning aisle of the grocery store and they do a really nice job of cleaning up both wire heddles and flat steel heddles.  Of course, if you're pressed for time, or if they're really far gone, you can always replace them with new ones. 

EPortabello (not verified)

What most of the people is saying about all these things that has got to do with all that is definitely making all of us getting so interested with it. It's the fact that weaving really adds value to our somewhat forlorn life. - Lindsay Rosenwald


sequel (not verified)

The green scouring pads are similar to "0" steel wool - very coarse and abrasive.  They will even scratch stainless steel.  Start with the least aggressive 0000, and try the next, 000 and the next 000 until you find one that will do the job with the minimum amount of abrasion.

Submitted by Anonymous (not verified) on