does any one know about Gillan shuttles. I can not find any info on them. I need a bobbin for one. it is 8" long and about 1" wide...

Comments

kerstinfroberg

You can always make paper quills - and have as many as you will ever need, and practically free, too! (as long as we are not talking about pirns for end-delivery shuttles). See (for instance) here.

oldfanny

I just received a bobbin winder from Sweden, just like the one shown in your example.  I find that the spindle is too small for the regular plastic bobbins I have, so I tried making paper quills.  That went OK for the most part.  The first one I made was too tight for the rod in the shuttle.  I made a looser one and that worked OK.  But the problem I am having now is that when the bobbin thread gets near the end, the quill seems to collapse and binds in the shuttle.  I have been using regular printer paper.  What am I doing that I should not be doing?

ZenSojourner

I don't know what's going on - but I had posted a response, it appeared, I noted a spelling mistake, went in and corrected that, tried to save that - and the entire post disappeared.  Just gone.  So - I'm trying again.  If 2 postings show up eventually, I apologize.

According to Glimakra:

"The fine spindle is more versatile as you can wind quills as well as bobbins. Just put a cardboard quill on the spindle and then put the larger bobbin on top of the quill. It usually is a perfect fit."

Of course that implies that you know what goes into making "a cardboard quill" (what kind of cardboard??? How long? Can you make a quill at all to start with?).

In case no one here knows how to do that, try posting on the Glimakra owners group at:

http://weavolution.com/group/glimakra-loom-owners

Joanne Hall, who IS Glimakra USA, is usually pretty quick to respond over there.  However she is on the road teaching this week and Convergence is next week so she may not be as quick about it as usual until after that is all over.

Andrew Kieran (not verified)

For making paper cheeses (quills, I believe), I tend to cut off a width-ways strip of A4 printer paper of the required length, then wrap this around a pencil and tape on the outside. It is generally strong enough as there are many wraps and it's about as thick as cardboard.

Andrew Kieran (not verified)

I should add I use the same pirn winder as Kerstin here and use it for winding mill-pirns for end feed shuttles. The pirns are too wide for the spindle so I just tape some paper onto the spindle to make it wider and jam the pirns on tight

kerstinfroberg

Could it be she (Joanne at Glimakrausa) is referring to the cardboard "tubes" available from them? (Here, towards the bottom)

Myself, I own 3 plastic bobbins (working with my winder), but never use them... paper is always to hand, need not be emptied.

ZenSojourner

Kerstin, that could very well be!  Seems that would be an excellent solution to the problem of American bobbins not fitting on the Swedish winders.

That would give oldfanny time to figure out how to wind her own quills should she still want to, and be able to use her bobbins in the meantime.

kddid

Another quick, cheap and easy quill is just using a cut-to-length plastic straw.  I'm all thumbs when it comes to making a quill!

 

Missus T.

The fine ladies at The Weaving Center in Tarrytown, NY taught me to make my own quills from ovals of paper cut from grocery-weight paper bags.  The width of the oval should be about 1/2 inch less than the width of the bobbin opening on the shuttle.  To wind the bobbin on a Swedish quill winder, handstart the rolling of the paper onto the spindle and catch the thread in the last roll around of the paper.  Then begin winding slowly.  Stay 1/2 inch or so to the inside of the edge of the quill paper so that the thread will not fall off the edge of the paper quill, and do not overload the edges of the quill paper.  The first time I did this, it was awkward, but once I got the hang of it, I'll never go back to noisy bobbins!  Good luck....

Missus T.

I forgot to mention one tip:  the Swedish quill winder spindle is tapered.  The end of the spindle is narrower than the portion of the spindle that is close to the gear and handle.  This is good.  Begin winding the paper near the thin end of the spindle.  When your hand slips and you fumble the paper roll a bit, you can snug up the "grab" of the paper on the Swedish quill winder by pushing the quill toward the fat portion of the spindle.  Most of the time the extra width of the spindle on that end of the spindle is enough to get  the spindle to grab the paper and allow you to wind the quill.  If it doesn't stick, then try again.  Roll the paper to fit the narrow tip of the spindle and then as you get a few rounds wound on, you can move the quill down to the fatter portion of the spindle. 

ReedGuy

I just use card stock. Roll it up using the spindle on the shuttle for the diameter and tape the paper at the end for a solid quill that lasts for a long time. I've never warn one out in 2 years. They go onto my home made shuttles. As far as the yarn bunching up, it's in the wind of the quill. I have woven blankets to dish towels to runners with them.

oldfanny

Thanks all for your comments and suggestions.   I've tried paper cut in ovals, tried paper cut in strips.  I haven't tried card stock yet, but will.  Two things that have happened:  first the thread seemed to bind on the bobbin, while in use.  The other was that the bobbin would work its way to the end of the spindle in the shuttle and bind on the woodwork.  I suppose both of these situations would correct itself with practice.  One work around solution I came up with yesterday was cutting a lengthwise slit in some plastic piping and fitting this over the spindle of the bobbin winder.  This "fattened" the spindle so that I could use regular plastic bobbins...looks amateurish, but it works.

 

ReedGuy

Put small washers on the ends of the quills with 1/8"-3/16" diameter hole in them. Just slightly larger than the shaft diameter the squill sits on. This will stop the binding.

You could also wrap tape on the shaft to fatten it to, if it was one dedicated to your particular bobbin. Just so your not tearing it all off again if you have other sized bobbins. We also wrap tape on winders to fatten them for pirns or spools. I do it all the time with my home built winder. It's a hand crank one.

ZenSojourner

Oldfanny, who cares how it looks - the bobbin fits over it anyway, so nobody can see it anyway!  As long as it works, that's the important thing.

oldfanny

I'm beginning to agree more and more about getting the job done rather than worrying about the looks of what I'm working on or with!  My old Fanny will attest to that.

 

 

FiberMusings (not verified)

Bluster Bay has some great instructions for making and filling paper quills. With some practice, you can wind your quills that will not slip off and bind up.

As for the paper, someone told me that she used old National Geographic and cut them up to make quills. I found that any magazines and/or paper catalogs with similar weight paper work great. (Old alumni quarterlies, Smithsonian Magazine, etc.) I just use rectangles.

I keep a short dowel to wind the paper on so that they all have a consistent diameter. A cheap round stick pen or pencil will do the same.

Submitted by cindybeck@mind… on