I just started weaving a shawl with an Atwater Bronson lace pattern and I am having trouble with the shuttle taking a nose dive through the warp with every 3rd or 4th pick.  The warp is 2/8 wool and I have the tension pretty tight.  I am working on a Julia 8 shaft countermarch loom.  I've never experienced it like this.  Usually it means my tension is too loose and once I tighten it everything is fine.  Not this time.  It's the first time I am using this wool and I have it sett at 10 epi.  The weave structure looks good but it's taking forever to get anything woven.  Do I need to sett it at 12? or higher?  I calculated the sett and checked it on the charts in Peggy Osterkamp.

I'm getting very discouraged and would appreciate any suggestions.

TIA,

Claudia

Comments

ReedGuy

The sett won't make a difference unless it's crowded in the reed dents so much that it's sticking. Is the warp sticking?

Joanne Hall

Hi Claudia,

The Swedish Tuna yarn we have can be sett at 10, which I do for the rigid heddle loom and the double weave blanket kit. But it can also be sett a little closer.  It is 6/2.  So, since your yarn is a little thinner, you might be right.  12 epi might be better.  But this may not solve the problem.

Are you throwing the shuttle with your palms up?  That can also be described as thrumbs up.  That position makes it much easier to throw and catch and to control the throwing.  Keep the shuttle level when you throw it.  You are not a beginner, so I don't know what else to suggest.

Joanne

ReedGuy

Sometimes a minor adjustment is called for with some tie-ups, likel a cord may be a little long or short from the treadle to a lamm. Or an upper and lower lamm are tied against one another and that shaft only opens 3/4 of the way or something. This happened to me on my last warp and immediately I went looking. Yup found it on one of the treadles, one lamm working against the other on one shaft.

Claudia Segal (not verified)

Well, I double checked my sett and the wool I'm using is 1440 yards/lb which, according to Peggy Osterkamp, is similar to the 6/2 Tuna and should be sett between 9 and 11.  I have it at 10.

I tightened up the tension and only lost the shuttle once in 6" of weaving so it seems to be better.  I am never certain how firmly to tighten wool.  It's easy on the rh loom because you go only tight enough for the heddle to stay in place. 

This is my first 8 shaft project on the Julia and I think, as you suggested ReedGuy, I need to work on getting the treadles and, hence, the shafts, a bit closer.  My sheds are clear but not really clean.  It's very clear where the shuttle goes but there is not a really tight bottom without cinching up the tension.

I also discovered I did not follow the threading draft correctly but it's still Atwater Bronson just not as nice.  Here's a picture.

Dawn McCarthy

Sounds silly but - are you using an open bottom shuttle?  If so check that your pirns/bobbins are not too full to interfere with the shuttle gliding across.  Just a thought.

Dawn

 

Claudia Segal (not verified)

Hey Dawn, Good thought but its closed bottom. I tightened the warp and it's much better. I still have to fix the sheds. They are clear but not really clean. I'll see if that helps. Claudia

ReedGuy

Yes, often time you should check the warp all over before you weave because just tying on can cause some areas to be tensioned more than others. If you begin tying in the middle for a few ends and then move outside for a few and "fill in" between after, most often those initial ends are now loose because you tied the "fill in" ones tighter. So as the "Big Book" says make a knot that can be easily undone before committing. She shows how to tie the knot. It might seem like a pain to commit to this idea, but your gonna be doing it anyway. ;)

Dawn McCarthy

And don't fuss too much with the upper shed, get the lower shed flat and not too wide a shed.  Hope you see an improvement.

Dawn

Submitted by Anonymous (not verified) on