I am warping back to front for only the second time, and I just don't understand exactly how I'm supposed to get threads spaced in the raddle.  As I understand it, the sequence goes:

1. Slip loops of warp over rod.

2. Lash rod to warp beam apron rod.

3. Put lease sticks into cross.

4. Cut ties.

5. Spread threads in raddle.

 

But if my raddle is on my back beam and the lease sticks are between the back beam and the shafts, the threads are already passing over it.  Last time (the first time I warped this way) everything got tangled up & while I straightened it out the best I could, there were still threads crossed between the lease sticks and the raddle.  It all worked out fine, but this warp is more delicate and I don't want to break threads.

Also, do I leave the raddle on while weaving?  I did until the end, then slipped the raddle out so I could weave closer to the shafts. 

If it makes any difference, this is a narrow warp (seven inches).

 

Thanks for any suggestions!

Comments

Sara von Tresckow

 1. Warp threads are only happy with some tension - at the point where you cut the tie on the cross and spread the threads in the raddle, the warp chain should be loosely wound once around the breast beam.

2. To avoid a tangle at the raddle, fold a piece of stiff paper or cardboard over the teeth where you are not placing threads and put the warp chain on this paper.

3. Count your threads out of the cross on the lease sticks and take only threads that are in sequence. That way the order in the raddle is the warping order.

If you had tangled and crossed threads, somehow you didn't pick them out of the cross in the correct sequence. 7 inches should make a good practice warp. Good luck.

laurafry

Like Sara, I've found that a little tension goes a long way.  A thread under tension is a thread under control.  :)

Cheers,

Laura

Michael White

Cynthia,

When you wind your warp, are you tying it in inch groups or some  other kind of plan?. Each section tied off should be the number of threads to go in each section of the raddle.  When you insert the lease sticks and then put the raddle in ( I slide mine in underneath and then support the raddle.) you loosen the ties and put each group into the section of the raddle.  Once the sections are in the raddle and centered on the loom, be sure you put a string or something over the top so the yarns can't pop off if something slips.  The raddle should be next to your harnesses and the lease sticks further back.  I do not tie the leases or raddle to the castle, but have  support sticks that goes from the front beam to the back beam on either side of the loom,   I tie these bars down and then tie the raddle and lease sticks loosely to these..  It will not slip off but can move a little bit and this helps when you are winding, as if there is a snag in your warp, the sticks can at least move and not break your thread.  After I get done beaming, I remove the raddle and move the lease sticks all the way up  behind the harnesses so I can thread.

Good luck and if you need anything clarified, just let me know.  Do you have a good book on basic weaving.?  Lots of the older books show back to front.   Be aware there are lots of variations of the process, but find one you are comfortable with and learn to do it until you are comfortable.  There have been several articles in Handwoven on the subject too, and there is a book out about Warping by Yourself by Peggy Oestrander, and I may be butchering the last name.  One last suggestion-Do you have a guild or group in your area?  They can be an invaluable resource and would probably love to help. What are you working on?

Cheryl White, Michael's better half

Cynthia

Cheryl -- oh, tying the warps in inch groups makes so much sense!  No, I have not been doing that, but I'll give it a try.

My loom is a baby wolf, and the raddle has special braces to attach it to the back beam, so that's where I've been putting it.  It's an x frame, so nothing runs from front to back; maybe I could rig up something.

Our local guild folded a few years back.  There's one (or maybe two) up in Oklahoma City, but I haven't been able to get to meetings.  Life is always so busy!

My current warp is for three scarves; the warp yarn is a cashmere / merino blend, and the wefts will be various handspuns, mostly silk or silk blends.

Sara von Tresckow

Cynthia,

It also works just as well to mount your raddle in the braces and put the lease sticks between the shafts and the raddle. The raddling step is quite importasnd, but the mounting of the raddle and lease sticks will vary from loom to loom.

In any case, it is also important to keep a little tension on the warp when spreading the threads. I personally have never done the raddle cross, but always make a 2 thread cross holding a finger between the threads as I put it on th emill  (that was the suggestion in the Lundell book when I used it back in 1981 to put my first floor loom warp on). When you raddle, picking one pair on one stick moves 4 threads. This makes it easy to count up to whatever number belongs in a raddle section. It is also not terribly bad if a thread or two finds its way into the neighboring space during beaming. Main thing is that the warp is applied in a consistent width to the warp beam.

I'm taking a break from beaming a short warp on a table loom - in this case the raddle mounts behind the shafts. On my other floor looms, it fits better on the back beam. After a few warps, it is just as easy one way as the other.

 

naturalfibres (not verified)

Here's a picture of how I put on a warp - back to front.

 

The raddle is just a piece of wood with nails put in every inch and held on the back breast beam with elastics.  Starting at the middle of the raddle I numbered each space - if it was 20" long here's what it would look like, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 1, 2, 3, 4, 5, 6 , 7, 8, 9, 10.  I then have the centre of the the back breast beam marked, so that I can line up the middle of the raddle on it - then my warp will in the middle of my loom - and not off to one side.

tnsinko (not verified)

man, i must be doing this the 'hard' way, but i'm following The Big Book of Weaving, running the ends thru the reed with a set of lease sticks on each side, then winding it onto the warp beam.  So Far (crosses fingers) this is my 5th warp, and i love her method.  it's tedious. it's time consuming, but you DON"T get tangles, and there are several chances to check the warp when threading and sleying.    I may try a raddle sometime in the future when i get a little  more experience.  Right now, though, My Glimakra Ideal seems to like the way i'm doing it.

Sara von Tresckow

 Yup - if that book had been available in English back in 1976 when it was first published, weavers here would have a much easier time of getting the loom set up. I learned when we lived in Germany, and my local independent book store found the title for me when I asked for something on weaving and dumb luck put it into my hands.

It has been the most popular book in more than one European country for good reason.

Check the front - Ms. Lundell wrote it when she was directory of the "HandarbeitsVenner" or Arts and Crafts School in Stockholm, AND its weaving instructor. It is truly a book you can depend on.

kerstinfroberg

And the school is still going strong ... http://www.hvskola.se

There is a page with information in English, but don't miss the slide show on the main page!

 

tnsinko (not verified)

wow.   it's wonderful....so much of her nit-picky methods make wonderful sense when i see other weavers at our guild making a dog's dinner of warping....tangled threads, crossed threads, Oh MY!!!  ;-)  

ingamarie

 I guess it's all what you're used to. I don't find her way nit-picky at all, but that's how I was taught!  When I see or hear about people warping other ways (and having all the problems) I always why they're making it so hard on themselves. Glad it's finally available in English.. I think Sara is right about that.

Loominaria (not verified)

 I'm glad Weavolution came to be before I've had much weaving experience.  I'm looking forward to getting into some good habits from the start from the many tips posted here.  I found this book at overstock.com -- thanks, Sara.

Kurt

laurafry

There is a very good reason to pick nits.  :)  I'd rather do a little extra preparation in order to make beaming easier, not to mention the actual weaving. 

It really isn't difficult once you get the steps in the process firmly in your mind.  The steps are all there for a reason.

Cheers,

Laura

home from a week away visiting with several weavers.  :)

Dawn McCarthy

I almost always dress the loom back to front.  As I have no assistance in doing this I have found having the warp chain in front of me , then the lease sticks in the cross and through the raddle to the back warp apron allows me full access to tensioning the warp whilst being able to reach the ratchet to wind on, works well for me.  I agree with rough sleying and using weights, but I have a 63" drawloom and 60 inch AVL in a tiny basement studio so this method works really well for me!

http://bloominloom-dawnmccarthy.blogspot.com/search/label/Warping%20Bac…

Dawn

Cynthia

Oh, my goodness, this is practically the same question I asked earlier this evening -- except that in this thread I asked it 2 1/2 years ago.  I'm hanging my head in shame here.  This time around I'm going to master back to front warping.

Cynthia

Ellen, thanks for that link.  Your photos gave me a lot of good ideas!

Ellen (not verified)

I'm glad you found them useful :-)

Gone

Okay. Newbie here too. I warp back to front and use a valet (thank you Laura Fry) I like that method. But it's just the way I started. In the books, videos and other information I've read, I'm being told to wind a warp with the threading cross at the beginning and the counting cross at the other end. The counting cross goes into the raddle. But the threading cross is at the other end of the warp. So how am I supposed to get my lease sticks next to the raddle if the threading cross is 10 feet away?  I just read something about doing a counting cross WITHIN the threading cross. That would put both crosses at the same end of the warp when winding on - at the warp beam! THAT makes sense to me! Otherwise I have to insert the lease sticks, slide them (hopefully) all the way to to other end of the warp where the raddle is mounted dividing the warp, and secure them. I keep reading, "divide the groups in the raddle....insert the lease sticks....." But my lease is at the other end of the warp!

I'm obviously not getting an important step here. Could someone explain? Do the counting and threading crosses go at opposite ends of the warp or not? Anything to clear up this confusion would be much appreciated.

 

Tom Z in IL

sandra.eberhar…

When I wind a warp, I wind a threading cross and a "counting cross".  I figure how many threads I want per raddle bunch and tie the warp into raddle bunches as I wind.  When I'm done, I start chaining from the threading cross.  When I beam, I slide each bunch in its place in the raddle. The warp unchains from the back (raddle cross) to the front (threading cross) I only actually use the raddle cross if there is some confusion about where a thread goes (rarely) or if there is an accident (like one of the pegs fell out of the threading cross) and the raddle cross now becomes the threading cross.  When I'm done beaming, the threading cross is there, ready to thread.  I use a valet or trapeze, and I do not use lease sticks.  This has worked very well for me for many warps, so what others have said about finding a way that suits you and your equipment is right.  For me, I have found the key is to keep tension on the warp with the trapeze.  I can hit or strum the taut warp threads to bring misbehaving threads back in line.

Gone

Thanks  BWSD. I understand what you're saying and it makes sense to me. I use a valet too. Tension is an enormous aid. I'm just confused on instructions which say to divide on the raddle then insert the lease sticks when raddle and lease crosses are at opposite ends. I think I'll begin doing counting groups as well at the threading cross end.  Then all my indicators are at one end of the warp. Being a newbie, I still rely on the lease sticks. And they would be necessary if I wanted to tie on a new warp. Thank you again.

 

CelticCats

Laura Fry's The Efficient Weaver has an excellent visual on warping back to front with presleying the reed. Ashford has a utube video on winding the warp and dressing the loom with a raddle. Both are excellent videos on back to front warping.

ladytj1754

I just tried something new in a warp. As I was winding on thE warp using a warping board, I counted at the cross and bundled there. Example: I needed 540 ends in sections in 30-end segments. That gave me inch groups before I ever took the warp off the board. Then, when I placed the lease sticks through, I had my sections all ready for my raddle. I had an 18" weaving width with 30 ends per grouping. With tension, I easily wound the warp in the back beam! Worked like a charm! All I had to do was string the heddles, sley the reed and I was ready to weave. I use a Mighty Wolf, 4-shaft loom. I used a partially filled gallon jug of water to tension my warp while winding onto the back beam.

pammersw

Ladytj, that is exactly how I was taught to do it! Warping does get easier with practice. 

Submitted by Cynthia on