I have been trying to assemble my loom. I have got most of it sorted but am stuck on what the connection between the treadles and the lams is (I hope Ive got the right terms). I have 6 treadles attached to the frame at the back. Then I have 4 lams attached to the lhs. What do I do next?

Many thanks

Paul

Comments

Dawn McCarthy

What kind of loom is it.  If it is counterbalance or countermarch it needs to be dressed with a warp before tying up the lams to the treadles.

Are the lams connected to the shafts?  The lams get tied to the treadles when you have your design and tie up plan.  The treadles need not be attached until this time.

Dawn

 

paulz

Good question. It seems as if it might be a swedish type loom. We have followed the instuctions (which has all the correct parts) from the big book of weaving. I am thinking it must be counterbalance since it has pulleys on. The other bit about the instructions is about the warp beam having a cord through it. Mine hasn't.Many Thanks

Paul

Michael White

Paul can you post pictures of your loom. This would help a lot in figuring out the set up.

Michael

kerstinfroberg

need not go through the beams, even if most Swe looms have holes. They do have to be fastened to the beams, though, so that they never slip. Or you can use an apron (basically a piece of cloth nailed to the beam(s).

And, IMO, the lams should not be connected to the shafts until after warping, as it is so much easier to move the heddles with nothing to hinder them (assuming string or texsolv, here).

paulz

Will put some on flickr once I've taken some. - Still cant work out what to do n this site.Paul

endorph

mean the studio construction is complete. congratulations!

paulz

I put the loom photos here. They are in taken in my new studio. 1305 one is general assembly. 1307 shows the lams/treadles. They are just like the ones in the big book of weaving but it doesn't seem to tell you how to sort the treadles and lams out. Also show is some bits I don't know what to do with. Any help appreciated ( I know 1313 are the bits on the back and front beam) but need help with most of the rest.

(Michael i promise to watch the video in the morning to sort out uploading pictures)

Thanks to all

Paul

ReedGuy

Looks like counterbalance. Photo # 6 looks like it's used during tie-up to hold the shafts even and level. Curved pieces are the horses for the harnases.

kerstinfroberg

And I agree with ReedGuy that 1312 is for holding the shafts during threading/tieup.

1317 looks to me like some kind of brace, to hold something apart. But what... might become clear later, when you see the flaws/problems... (my old loom had some strange pieces which turend out to be a reinforcement for when using all shafts - after the last move I didn't bother to put them back, and don't need them)

1313 - apron with tie-on rod?

How to sort lamms and treadles: each lamm should hang directly under it's shaft. (If you are using just 2 shafts, take the other two lamms out) The holes in the lamms should hang directly over the treadles - the lamm-treadle cord should be straight (vertical). The lamm can be connected to more than one treadle, and each treadle might be connected to more than one lamm. You should see the tieup diagram on top of the lamms. (Clear as mud?)

ReedGuy

Your centre hole on your lamm bars attach to the lower shaft bar. This is in the centre of the loom for ballance. Photo 1307. The round dowels are for the pulleys to hang off to support the horses, which attach to the upper harnass bars. Photo  1316.

ReedGuy

The "Big Book of Weaving" would solve the mystery for you somewhat. The book is good for content, but poorly organized. You have to look all over the place for the information. ;)

Submitted by paulz on