New loom question. With the Harp in a stand, and adjusted at a comfortable working angle, why won't the heddle stay in the block in the UP position? It just falls forward, and tightening the tension doesn't help.

Comments

Claudia Segal (not verified)

I have a Harp too and am trying to think of what might be going on.  Perhaps you have the heddle block in the wrong holes?  I'll check on mine in the morning and if you can take a picture or two and post them here that would help a lot.  I gather you have a warp on the loom, right?

Claudia

sewdoggie (not verified)

Yes, I have it warped and have started weaving. We assembled it exactly like the directions say and show, there's nothing to hold it in the up position. I'll take a pic in the morning.

Claudia Segal (not verified)

My Harps have 3 positions on the heddle block; up, neutral and down.  The topmost position which is the up or holes up position has the bottom of the heddle resting in the top of the heddle block.  Like this: 

Sometimes it's the easy things that get past us in a new loom so pardon me if I ask some things which may seem obvious.  The Harp is designed for you to rest the bottom of the heddle in the slots on the heddle block.  Is that how you have it?  I'm just trying to think of everything possible.  When I was trying to weave on an older model Schacht rh loom, I had the heddle upside down.  Kromski has their name stamped on the top of the heddle to help guide you.  On one of my Schachts the bottom rests in the heddle block, on the other it's the top of the heddle so you may want to check where your heddle is on the Harp.

Does the picture I posted help?  It does show the heddle leaning forward quite a bit when the loom is tilted.

Claudia

sewdoggie (not verified)

I'm feeling really stupid at the moment, because I knew the Kromski name was to face forward. When you mentioned it, I checked, and it's facing the back. One of those duh moments, cause I did know better. However, I don't see where that changes anything, there's nothing on the heddle that would change what's happening if it were in the correct position. I'm waiting on my battery to charge, would just figure it went dead when I needed it. Posting a photo the minute it gets up to speed.

I'm noticing your heddle block appears to lean forward? Mine is straight up and down. Am I seeing it in your photo correctly?

Marsha A. Knox (not verified)

You have your blocks correctly.  Maybe you have the loom it self tilted too much.  As for the heddle itself, which way it faces won't matter...if it is upside down I believe that it will.  Did you remember to have the heddle in the 'neutral' position while you were tying on?  If it was in the up or the down position, it makes the tension of the warp funky and this will effect whether or not the heddle will sit up like it is supposed to.  Also when you put the heddle in the up position, if the loom is tilted too much sometime sit helps to push the top of the heddle a little towards the back of the loom.  Hope this helps.

sewdoggie (not verified)

I definitely had it in the neutral position while warping. I set the stand at an angle to weave comfortably sitting down, this is when the heddle wants to fall forward. I've now put it back to completely level. What is the purpose of a stand that adjusts if you can't use it that way? I did try to "settle" the heddle back against the wood to rest with not much luck. It will unexpectly just fall forward.

clgy (not verified)

I'm new too, so take this for what it's worth. You shouldn't feel bad.....I actually didn't realize there was a "neutral" position, and was wondering why I couldn't get a shed in what I thought was the low position. :) However, I haven't had any problems with the heddle falling off in the up position. Maybe you should try adjusting the stand to be slightly more level and not quite so much at an angle. I have mine situated like a slightly sloped school desk and it works fine. Also, with the heddle in the neutral position, try tightening the tension just a little more; that is sure to help. Good luck! 

Cindy

 

Claudia Segal (not verified)

Hi Sewdoggie,

Cindy has some good suggestions.  I just wanted to let you know that your photo link is there.  To upload the photo so it is part of your message, take a look at this topic in the Help section.

Let us know how it goes when you raise the front up a little and tighten your tension a notch.  Hoping that does the trick.

Claudia

sewdoggie (not verified)

Cindy, yes you had the right answer! I didn't have the heddle in the neutral position while tightening the warp. Seems to be staying in place now, and I was able to put the loom back to a slight angle. Thanks to all who responded! (I'll get this yet)

 

**edit: I did have in the neutral pos. while winding the warp, but then after starting to weave, and went to take up the tension a bit, and didn't have it in neutral.

clgy (not verified)

Awesome......my first time to help someone, and I have only been here a little while! :) I think these online groups are fantastic, and I hope to share and learn here for a long time. 

I think I answered that in a roundabout way....but just to add to it, any time I need a breather, I just naturally put the heddle in the neutral position, because it seems to "stay" better there. Also, it reminds me to *think* before the next throw, as far as whether I should be "up" or "down". By the way, I didn't buy the stand at first, but have one now, and absolutely love the extra convenience of being able to weave anywhere, without balancing on a table!

Have fun! 

Submitted by Anonymous (not verified) on