I would appreciate some help in finishing the tying up of a Lillistina 4 shaft loom.  The current setup is as follows:

The Shaft Horses (Rockers) are tied up:

Left Side Front rocker.  Outside to Shaft 1 - Inside to Shaft 2

Right Side Front Rocker.  Outside to Shaft 1 - Inside to Shaft 2

Left Side Rear Rocker. Outside to Shaft 3 - Inside to Shaft 4

Right Side Rear Rocker Outside to Shaft 3 Inside to Shaft 4

The Lams are connected to the treadles as follows, numbering from front to back on the Lams and left to right on the treadles.

Lam 1 to treadles 2,4, and 5

Lam 2 to treadles 1,5 and 6

Lam 3 to treadles 2,3 and 6

Lam 4 to treadles 1,3 and 4

 

With the above tie up. How should I connect the Shafts to the Lams?  Is it simply Shaft 1 to Lam 1, Shaft 2 Lam 2 etc.

 

 

 

Comments

Mike (not verified)

Thank you Joanne;  hopefully I can soon start to weave on the Lillistina.  All I have to do now is warp it on my own.  I have had one lesson so time to go solo.  Stand by for further please for help!!

Kind Regards

Mike

52ZOZARK WEAVERS (not verified)

Just got one to work-on and wonder'n-how-the-warp'n's-ago'n????????????

Found out the old warp'n-on-it's a ' plain-twill ' go'n-down-to-the-right!!!!!!

What did you decide to try on yours??????????

Don't forget pics-save-alota-typ'n!!!!!!!!

KEEP-HAPPY-WEAV'N, WE-SURE-DO-----B/SUE & 'OLE-LOU' HERE!!!!!!

52ZOZARK WEAVERS (not verified)

THANK-YOU-KINDLY, JOE. You are a walk'n-book-of-knowledge!!!!!!!!

That manual is just what we been looking for!!!!!!!!!!!!!!!

Mike (not verified)

Thank you for the reference for the manual.

I now know how to attach the Lamms to the Shafts and am aware of the way to tie up the Treadles to the Lamms.  But what should the sequence be, and where should the shafts be, when tying up the Lamms and the Treadles. i.e.

Which should be attached first - Lamms to Shafts or Treadles to Lamms and then Lamms to Shafts?

Where should the Shafts be positioned when tying up the Lamms and should they be held fixed in this position until the Lamms are tied?

kerstinfroberg

First, position the shafts so that the warp goes through the middle of the heddle eye.

With the shafts fixed in that position, attach the lamms, then the treadles. (I don't think this order is crucial - it's just how I learned...)

Now, with the warp in place and tensioned, lamms and treadles tied, free the shafts and test the sheds. If something needs to be adjusted (and probably *something* does), re-position the shafts and do the adjustment.

Test again.

And, remember - it is the *sheds* that count! It doesn't matter how the warp/shafts/treadles look when resting - .

Mike (not verified)

Thanks.  I'll try that

Mike (not verified)

Success!!  For those who might be faced with a similar predicament in the future, this is how I did it. 

The Treadles were already attached to the Lamms as set up by the previous owner of the loom.  With the loom threaded and the shafts held in a mid-position, such that the warp thread went through the middle of the heddle eyes, I then took the weight off the Treadles by placing a stick underneath them, the ends of the stick being supported by the metal side bars of the loom.  I then supported the lamms by a piece of cord such that the free ends of the lamms were just above the horizontal.  It was then just a matter of dropping the Texsolv cord from the middle of each shaft down through the appropriate hole in each Lamm, and then securing the cord with the Texsolv fastener.  Thereafter, it just required a little bit of fine tuning up and down on the Texsolv.  Thanks for the guidance and I hope this helps someone else.

Michael White

Mike, You may have it right, but just in case. The warp threads go through the middle of the "reed" on a counter bal/mar loom when it is at rest. You adjust the height by moving the heddle frames up or down.

Have fun weaving on your "new" loom. Like Claudia says, "Pictures, pictures and more pictures"

Michael

kerstinfroberg

Michael, I beg to differ.

The warp has to go through the middle of the heddles *first*. If the reed interfers with the shed, then it is the *reed* position that should be adjusted.

On a CB and CM loom the warp should be in a straight line from the back beam to the breast beam.

Mike (not verified)

By good fortune I managed to achieve both!!

Michael White

Ok, I am guessing on this loom you can adjust the postion of the reed,  thanks for that information. I know about the straight line, and on jack looms the line dips down.

Michael

Submitted by Anonymous (not verified) on