I thought I'd share this from Walter Turpening, posted many years ago on the Weaving yahoo group (and reposted with his permission).  We were discussing benches a little in another thread.  I've used this method on several benches/ chairs and it's always worked well for me.

Lower Leg length (LL)- from floor up to the back of knee(where the little crease develops when the knee is bent)
Treadle Height (TH)- from floor up to top of treadle where the ball of your foot rests before treadling



add LL to TH to get Lower Torso bench height: ex. LL = 18", TH=3" gives a LT=21"



Elbow Height (EH)- seated from seat up to bottom of elbow with fore arm horizontal and upper arm vertical.
Breast Beam height (BB)- from floor up to top of breast beam.



subtract EH from BB to get Upper Torso bench height: ex. BB=30", EH=8", gives UT=22"



Choose the higher of the two bench heights to assure that your elbow clears the breast beam and that your knee is at or below your hip when you begin to press down on the treadle.



Now in your case where you and the loom are not a perfect, treadle risers are easily done. A local woodworker should be able to do the job and a local lumber yard (not a box store) should be able to point you to one. Simple wood blocks attached with the best quality double sided carpet tape should do the trick. Their thickness is calculated by reversing the above equations.

That is, take the Upper Torso bench height UT and subtract your Lower Leg length LL and you get the needed Treadle Height TH   UT =22", LL=18" so the TH needs to be 4" and 1" blocks need to be made and attached.

Using the good carpet tape assures that they stay in place without mechanical damage to the treadle wood. Fireside Fiberarts makes clip on treadle extenders and a few of the other loom makers do also. You still have to make the calculations.



from Walt T.
Benches, Stools & Chairs

Comments

Trapunto (not verified)

 Thanks so much, Ingamarie.  This is the first time I've seen the difference between optimal bench height in relation to the treadles and in relation to breast beam taken into account.

Artistry

I just ran across this thread and am hoping that someone will have advice. I have been experiencing lower back pain which the doctor believes is from years of weaving. I found the above discussion helpful however I feel that what I really need is to sit upright with a back on the bench. I have an AVL compudobby , and I do tilt forward when I weave. Anyone else have this problem?

laurafry

Are you sitting on your tailbone, or on your hip bones?  If  you are sitting on your tailbone, there is a lot of stress on your lower back.

At my AVL I don't use the attached bench.  I found that if I tipped it forward enough that it didn't cut of circulation to my legs I slid off.  So I removed it entirely and sit instead on a tall stool.

Cheers,

Laura

Joanne Hall

You also need to be close enough to the breast beam.  Sitting up higher might also help.  If you are not sitting up close, you are probably bending forward when you are weaving.  This is especially important if you do not have long arms.  When you bend forward, you are not comfortable and you back may tell you so.  So try getting up closer. 

Traditional looms have what I call a belly board, a fabric protection board, so you can actually be rubbing against the fabric as you weave.  I teach at an art center in Minnesota where they acquired a 100 year old loom made by immigrants.  It has one of these boards on the breast beam.

Joanne

claudia (not verified)

I have used this formula and it works really well.  Once I got my bench adjusted correctly, I was much more comfortable and wove for longer without any back pain.

Claudia

ingamarie

You also need to be close enough to the breast beam

Joanne is absolutely right-- I sit right up against the 'belly board' and it really helps. I also find that if I 'plant' my self before starting... engage my core as they say in yoga class :)  that also helps. If I think of moving my body as a whole, and not just my legs and arms.  I don't know if that makes any sense or not, but it works !

Michael White

When I build my benches I make the front lower then the rear. Remember to exercise and stretch your back and  stomach muscles. This only takes 5 minutes. Get up and move a round to keep your blood moving. I know that sometimes with a computer assisted loom you just want to go and go. Well try moving the bench and weave standing up for a bit.

Happy, healthy weaving

Michael

Artistry

Wow! Thanks so much for the input! I'm going yo try all these things since they make so much sense. I think sitting up higher with a stool will work well. I often weave wider pieces 35 - 45in. And find i' m really leaning forward to throw the shuttle.sitting up higher,with a belly bar, engaging my core ( for as long as I can:) I think will work, and the frequent breaks that I forget to take, because I'm too excited about what I'm weaving! Thanks again for the help. I'm doing a tapestry now, but when I get back to the avl ( in a couple of weeks) I'll let you know how it is working out.

ingamarie

I have a few tricks to get me to get up from the loom: one is to not advance the warp from the front. I weave on a Glimåkra Standard mostly, which requires me to get up and loosen the warp from the back.  There is a mechanism that is supposed to let you do that from the front, but I don't use it (and it doesn't work very well either).  The other is to only wind a few bobbins at a time, so I have to get up to wind more.  I know those things cut down on your 'efficiency', by breaking up the work, but I guess I take a long view of what that means.

Cotton spinner

Michael I am going to construct a bench with a fixed slopping seat. Have you any recommendation for the slop. The seat will be about 10" wide and 22" from the floor. Do you think a 1" slop would be enough? Vince

patweaves

For my Mighty Wolf, I needed a smaller bench, and love the one by Harrisville Designs (which I used in weaving classes).  It's lightweight and easily adjusts to a steady seat, or slightly rocking.  The slightly rocking position is much more comfortable than my former Schacht bench (which could be adjusted to a steady sloping position - but I always felt like I was about to slide off!) - and it's much easier on the lower back!

The handles make it very easy to move without bending over too far; it quickly adjusts, so I can move it to the back of the loom for threading at a nice low level.

Thank you so much, Inga, for posting Mr. Turpening's egonomic advice: I have since adjusted my bench 2" higher and am anxious to see how that helps!

Vince, in terms of the slope when the bench rocks, the best I can tell with a "course plotter" (from former sailing days!) is about 11-12 degrees of slope.  Don't know if that helps your planning process or not....

FYI, here are the specs and a photo from the HD website:

large (9" W; 32" L; adjustable height 19-25"; 23 lbs)

small (9" W; 27.5" L; adjustable height 17-22"; 16 lbs).

large:  http://www.harrisville.com/product-p/a302.htm

small:  http://www.harrisville.com/product-p/a301.htm

Monica Bellas (not verified)

My problem is, I think, that my loom is too low.  I measured the breast beam and it's at 32".  I'm 5'7" and long waisted, and my shoulders/neck get tight after 20 minutes of weaving.  I've seen folks suggest raising the loom with blocks; but how do you attach them?  With the carpet tape someone suggested above?

Monica

ReedGuy

Pat, I think he means where the seat comes down over the uprights. The slop in the insert area to allow the bench to rock. I made one here like yours Pat, only mines pegged And you can take the bench rockers and flip them if you don't want to rock. They are arced on one edge and flat on the other. But on a loom, you will want to rock because it's easier on the body.

My bench

patweaves

Your bench is lovely, ReedGuy... beautiful workmanship!  The peg is quite clever for ease of disassembly.  A similar design to the HD bench, it appears that your insert is a gentle (arced) curve, rather than the straight slopes (forward and backward) on mine.  I would imagine that produces a smoother rocking motion - very nice!

ReedGuy

Yes, it moves as natural as your body. You don't even notice it. :)

Submitted by ingamarie on