So I warped my loom, threaded the heddles and the reed and tyed off - looked and I somehow missed the back beam bar!

Do I need to  completely restart  or can I just chug along?

Its on my tabletop lecler loom I am weaving a scarf.

 

ACK

 

Comments

KarenIsenhower

Most of us have done that at least once. When I did it on a portable loom, I waas able to unscrew the back beam, reposition it under the warp, and then put the back beam back in place. I don't know how your loom is made, whether that's an option or not.

Elk Ridge Orch… (not verified)

good idea

but not an option

 

sick about it

 

sally orgren

And I am not blonde ;-) Can you advance the warp through the front completely so you can release it from the back, go over the back beam and then re-tension it? At least you won't have to rethread everything. Is the warp strong enough to survive the process?

SallyE (not verified)

If you can't remove the back beam, get a piece of wood or metal and slip it under the warp and then screw or clamp it to the frame just forward of where the back beam is.   When you are done with this warp you can remove that and go back to using the real back beam.

 

Elk Ridge Orch… (not verified)

pondering that now

not that many ends but just a pain in the rear

lilyspin

The temporary back beam is probably a good thing to try, especially since it is a table loom.  

I did this on two consecutive warps.  I re-threaded both warps, assuming that a painful solution would be more memorable, so i wouldn't do it again.  Didn't work the first time, but the second time seemed to do the trick.  

sally orgren

How long is the warp? If less than 5 yards, you *definitely* can beam it all to the front and then adjust, or use a "dummy" back beam to lift the warp into position. (Dummy back beam is less work, less abraiding to the warp.)

Walkingquail

Don't beat yourself too hard, everyone has done that at least once!

I beamed forward and re-tied I re-wound when I did it and have always double checked myself since then.

Elk Ridge Orch… (not verified)

so my warp is 190 inches long, but only 40 end

ended up rethreading it I was just doing my whining a bit I am workign with soy silk for both warp and weft Will let you know the outcome I just did a small sample, cut it off and washed it and now it is drying.

ReedGuy

I don't know how your loom is constructed. But on my warps I use lease sticks at the cross. I would just remove the tie on stick from the looped beam cords and put the cords up over the back beam and rethread the warp loops onto the warp tie on stick. Then retension. Your warp is such a short one and very narrow that the proccess might take 10 minutes, probably less.

ReedGuy

You can see my lease sticks near the back beam. These just slide through the warp. The back lease stick is pretty much equivalent to the tie on bar. Meaning the loops from the warp cross would come to rest at the end of the warp chain on that back lease stick. Only now the warp is wound on the roller, the lease sticks are forward and the loops are now on the tie on bar and wound on the roller. So in your case with the short warp, just unwind. The reed assures the warp is spread anyway. Pull the tie one bar out, put the beam cord loops up over the beam and thread the tie on bar back through the warp and beam cord loops. Pretty much backing up and then going forward. :D

Elk Ridge Orch… (not verified)

thanks everyone for your help

I just rethreaded it nice and easy I didnt use lease sticks to warp it so if I had I would ahve noticed it now on to the weaving part!

sally orgren

Elkridge, Glad to hear you worked through it.

For anyone else facing the same problem in the future—when a loom is threaded, you can nearly always reintroduce your lease sticks if they have been removed.

Just treadle plain weave, inserting a stick with each pass. Lash them together or tape them together. You can insert them infront or inback of the castle, where ever you need them. (When I am tying a new warp to an existing warp, it is helpful to have everything hanging in order at the front of the loom.)

The only time this might not work is if your pattern doesn't have a tabby. However, many times when we need to reintroduce lease sticks, we are basically trying to keep the warp threads in order, so this may still work for your purposes, even if the warp threads don't fall 1 over, 1 under.

Submitted by Anonymous (not verified) on