Weavers, I need help.

I am on page 222 (draft #712) of Carol Strickler's A Weaver's Book of 8 Shaft Patterns. When I treadle the surface weft shots, there is nothing to hold the shot in place. The treadling sequence calls for the two picks to be in the same shed. Please help me understand where I am going wrong.

Thanks, Vicki Allen

Comments

Su Butler

HI Vicki....I am a little unsure of what you are asking, but I am going to assume you mean there is nothing keeping the first shot in the shed while you throw the second shot in the same shed? If that is the case, you must use a floating selvedge and make sure the pattern weft wraps around it after each shot. IF you mean that the warp floats that tie the pattern weft in place are not rising for these picks, you need to check both your tie up and your threading to make sure you have correctly threaded and tied up the pattern so these warps will rise when required to tie the weft floats to the surface of the cloth. If neither of these is the issue, can you please be more specific? Su :-)

Vicki Allen (not verified)

Thanks, Sue,

I'm going to recheck everything to see if I have threaded or tied up incorrectly. But even just looking at the diagrams, I don't see how it would work.

The directions don't mention using a floating selvedge as being necessary, but I will if I have to. I will let you know what I find.

Vicki Allen

mrdubyah (not verified)

Maybe this is an overshot draft?  In overshot weaving you need two shuttles.  Each shot with the pattern weft is followed by a tabby shot (usually similar to the warp) to form the fabric and to separate multiple shots in the same shed.  Many overshot patterns don't show the tabby because they assume it is "understood" as part of the weave structure. Could that be the problem?

Vicki Allen (not verified)

Thanks for the help, Su and mrdubya.

The pattern is not overshot, it is a supplementary weft pattern, there is no way to make a tabby sequence with that tie up. (I tried. I originally wanted to have a plain weave border all the way around the piece. It involved more pickup than I wanted to do so I abandoned that idea.)

Madelyn van der Hoogt of Weaving Today suggested I "take the shuttle over or under an edge thread between picks". This sounded like a solution, so I tried it.

 I tried taking the shuttle under/over a thread at the edge of the pattern area but since it was also going under the two lifted warp ends, that made a three-end "dash" on the back of the fabric. I am aiming for little or no color on the back.

I slept on it last night and I have some more ideas. I have increased the number of pics between the supplementary weft insertions to 6. I am going to try using two shuttles for the supplementary weft and, holding them out til I have woven three pics, then taking them around one (or two) of the weft pics then holding it out till it is time to weave it. I think this will only give me a "dot" of color on the back side.

One of the most fun parts of weaving is figuring out how to get what you want.

Vicki

Sara von Tresckow

Where to start here. Your two supplemental picks in "the same shed" do call for some type of anchoring on the edges. If they are not fastened by something like a floating selvedge, they might pull out in use later.

Your fabric consists of what appears to be tabby with some warp floats built in to hold those supplemental wefts. Those floats alternate. At the point where you place the two supplemental picks in the "same" shed, you are at the dividing line of those alternating warp floats. The first supplemental is held in place by floats A and the second, after a few more picks, will be held in place by the floats B.

When you reach the last pick of the floats B, you throw two supplemental picks again - the first held in the B group and the second will then be fastened down by the A group.

When planning a project using a draft and photo from a book, it is highly recommended that you plan for the edges, centering of any pattern repeats, and color changes both front and back before beginning. Modern weaving software has largely replaced graph paper, but project planning is still very essential to producing the fabric we envision.

Also, careful study of the photo compared to the drawdown can save lots of frustration.

Vicki Allen (not verified)

Sara,

Thank you.

Vicki Allen

Vicki Allen (not verified)

Thank you all for your help.

I did not make it clear that I am using this pattern in a scarf and it is in the center with plain weave borders on each side. I apologize for that.

I have worked out a way to anchor the supplementary pass that had no anchor and it is looking good.

 On the first supp. weft pass I am bringing the yarn straight up and through the next group of lifted warps. On the alternate supp. weft pass, I am carrying it through the lifted warps then weaving half of the in-between picks and anchoring it by taking it around the next weft shot 3 warp ends outside the last lifted group on each side. That holds the tiny dot of color in place.

 This makes the pattern section have a regular edge going up the side of ) and > and ) and > . I hope that I have been able to describe it.

I'm hoping to post a picture of it on Weaving Today and Weavolution sites when I finish.

Thank you all for your time and help.

 Vicki Allen

Submitted by Anonymous (not verified) on