Hi!

I am a fairly new weaver that was generously gifted with a Shaw Island Fleece Company countermarch loom (approx. 48" weaving width) by my aunt. My previous experiments in weaving have been some work with an inkle loom, and a few scarves on a small, 16" Dorothy, so I've never done anything involving treadles. 

Here is my problem: 

I am planning a few scarves for christmas gifts, and decided to use the big loom (this is my first project on this loom). I got the warp on there ok and was incredibly pleased with myself... until it came to tying up the treadles/lamms. I really wasn't sure how the thing actually worked (I had the general principle, but wasn't sure about the particulars), so I was mostly trusting my fate to several countermarch pages on the internet that had instructions on doing a tie up, since I don't really know anyone else that has this kind of loom. I am not doing anything fancy, just a diamond twill, so my tie up for the 6 treadles is (from left to right): 1&3, 2&4, 1&2, 2&3, 3&4, 1&4. This is, as I understand it, a pretty common tie up for a multitude of simple patterns. 

Once I got everything attached to everything else, the shafts are going up and down, but I am barely getting any kind of shed. I've tried raising and lowering the shafts themselves, and raising/lowering the height of the treadles, but it doesn't seem to help. I am wondering if there is any trick to getting a bigger shed? 

Thanks!

Comments

ReedGuy

Yes, any number of things going on.

Any of the treadles and lamms colliding when going up and down? Sometimes the treadles are too low (will hit the floor when fressed) or too high (slapping the lower lamms when pressed), or the upper lamms might need to be slighty upward when tied  so they don't collide with the lower lamms. Might need to adjust the harnessed up or down to centre in the reed. But just as important, you don't want the heddles, when at rest, to be pulling up or down to centre the warp in the reed. The warp from the back beam to the breast beam should be a straight line passing through the middle of the heddle eyes. This does not mean level, since some CM have the warp slightly elevated at the back beam.

Hope this helps some. :)

debmcclintock

Another simple mistake is that one of the lamms is tied to the wrong treadle and the crossed tie up is keeping the shed from opening. Check that all are going down to the correct treadle. Good luck and take your time. CM tieups take longer to understand but once you get it you'll be fine. Ps. Is your warp on the loom and tied with some tension. That helps also..

Joanne Hall

One time a weaver called me for help.  However she lives two states away.  I was planning to go that way, but it was still out of my way.  After many discussions, I decided to visit her.  She already had two weavers visit her and they both said that they were not familiar with countermarch looms.  When I looked at her threading, I realized that it had nothing to do with the countermarch.  When she threaded, a simple 1,2,3,4, she had pulled the threads forward to sley the reed, but she put the threads on the wrong side of the front heddles.  So, every thread twisted right between the shafts.  She did this so cleverly that no shed could open.  So, yes, there are many ways to make mistakes.

Joanne

GearRat

I sleyed front to back, which I found easier given that I can stand inside this behemoth to do it, lol. I am getting a small shed and it seems clean, but it's just not very big. I am thinking it is something to do with the length of my ties... I can hear something clonking when I depress the treadles, but I have yet to diagnose what the clonking is. This is my first time tying up any loom, so I am not entirely sure how high the treadles are supposed to be. 

Thank you for the glimakrausa link! That is incredibly helpful... I hadn't been able to find much information on countermarch looms that was terribly informative. Honestly, what I really need is a video of one working so I can compare, but, alas, youtube has failed me. 

mrdubyah (not verified)

Perhaps you're not getting a shed because nobody told you that every frame must be either pulled up or down on each treadle.  Are you, perhaps, forgetting to pull down on the unlifted lamms?  That would leave you with only 1/2 a shed.  For example, if your first treadle lifts 1&3, it must also pull down on 2&4.  To do that, you have to tie the first treadle to the lifting lamms for 1&3 and to the pull-down lamms for 2&4.  Same for all other combos, i.e. tie treadle 2 to the lift lamms for 2&4 and the pull down lamms for 1&3, tie treadle 3 to the lift lamms for 1&2 and the pull down lamms for 3&4, and so on.  Hope this helps!     DRW

Joanne Hall

It may also be as simple as your perception of what a good shed is.  It should be about 1/4 to 1/2 inch taller than your shuttle.

Joanne

Claudia Segal (not verified)

There is a great DVD made by Becky Ashenden from Vavstuga.  It helped me a lot.  So did Joanne Hall's book, Tying up your Countermarch Loom.

I had a horrible time tying up my countermarche after being successful several times.  Turns out I had forgotten to insert the locking pins. It makes all the difference in the world with the locking pins in the top jacks.  Where do you live?  One of the countermarch weavers on Weavo may be nearby.  I am in Maryland near Wash, DC.

Claudia

GearRat

I am just outside of Baltimore City. My boyfriend's mom is the only other weaver I know around here... I think she belongs to the weaver's guild, but she doesn't think that anyone has a countermarch. 

Are the locking pins supposed to stay in for the duration of tying this thing up? Once I got everything tied to everything else, I pulled the pins to see if everything worked. Just my luck that one of the ties from the top levers to the bottom lamm snapped this afternoon... I think it screwed a lot of things up. 

I also found out what the clonking was... When I depress one of the treadles, the other ones go up and smack the bottom of the cloth roll. I have my treadles tied up so that they're about six inches or so  off of the ground. Is that a good height? 

celtinbirks

Last year I purchased a vintage CM loom. I had an experienced weaver come and help me, read articles on the internet, and it still wasn't right. After weeks of stress, I was about to rip my hair out when I gave in and finally got Joanne Hall's book, "Tying Up The Countermarch Loom". It was like magic for me and worth every penny. I got the loom up and working in a few hours.

Don't give up! A CM loom is an amazing thing once it is working correctly.

Good luck!

ReedGuy

How high is the bottom cross member that holds the loom halves together? The treadles at rest should not go above this, mine are down an inch or so below the top edge, but could go even lower. Which leaves the treadles 8-9 inches below the cloth beam. My dimensions can be different than yours because every loom maker has their own design. The treadles do not need to be higher than the length of the heddles from the eye to the shaft bottoms, plus maybe an inch or less. If they are too high your foot at rest on the cross member will be in collision with the treadles and cause you grief. You will be cussing under your breath. ;) You use different length tie up cord, with the shortest to the back, progressively shorter to the front. The back cord on the treadle determines the height of the treadle, the rest are more slack. Since your treadle action is a lever, the motion is much different than say a car lift.

 

Make use of the locking pin in the jacks as well as the shaft holders until everything is tied up. Remove, then adjust if needed. When you pull the pin and shaft holders off the loom everything should be at rest.

MaryMartha

First of all, GearRat, congratulations on getting this far on your own.  

I endorse both the recommendations in Claudia's post, but primarily Tying up the countermarch, for now.  Tie-up is a difficult thing to photograph or film and that's where Joanne's descriptions and line drawings really help. 

Because all your sheds are clean, though small, I can't think there's too much wrong with your tie-up, even if it could be perfected. Are you holding the beater back with your hand as you insert the shuttle? When weavers used to undeslung beaters approach a countermarch with an overhead beater, they sometimes expect to leave the beater in its rest position - at the bottom of its arc - while inserting weft.

 The beater should be held on the back swing of its arc, almost against the heddles.  This increases the size of your shed.  This is especially important for me because my arms ar short, so I weave with the beater in the foremost of its three cradles. 

kerstinfroberg

While I agree that the locking pin(s) should be inserted while doing the tie-up, I do not agree with ReedGuy when he writes "when you pull the pin and shaft holders off the loom everything should be at rest". This is the ideal result, but it is not necessary.

IM (not at all) HO, the *only* result that counts is that the sheds are good - and I will go further: that the shed *floors* are good. If the top of the sheds are uneven does not matter, as long as the shed is tall enough for your shuttle. How things look when you are not weaving is just appearance...

ReedGuy

Kerstin it indicates things are in balance, and maybe less adjustment required. But it does not eliminate adjustment always. I guess I'm just used to it being well balanced when I pull the pin and the shaft holders on my loom.

EleanorPeregrine (not verified)

Being a relatively new countermarch weaver as well and having woven on a (now sold) Schacht 46" floor loom (which I loved), I have been following this thread with great interest.

I purchased a 48" Cranbrook at an auction.  It was in pieces, but save for a few small pieces of replaceable hardware, in excellent condition.  Research on the information from the plates told me that it was built in 1978.  I searched around online and found assembly instructions from several sources.  Two months later - I work more than full time - it was together (pats self on back).

I just completed my first project: two very small plain weave rugs for my mother, and noticed that the 1&3 shed was larger than the 2&4 shed.  I miss having a race along the beater like the Schacht had. 

Now that the rugs are off the loom, I will be putting on a sample warp and really getting to know the tie-up ins and outs.  Thinking I might get a big strong man to help me get The Contraption up on blocks to make it easier to experiment.

Thanks to the OP for starting this thread, and to the learned and experienced weavers who answered.

kerstinfroberg

Quite :-) However - my "cobbled-together-loom" has it's own preferences: if I use  > 10 shafts, the whole shebang always sinks a bit when locking pin is taken out - *without compromizing weaving functions*. And, after all, I'm interested in weaving functionality, not *looking* at a perfectly balanced loom "at rest" :-)

(Meaning: if the shafts move when you take the pins out - *do* try the sheds before you think you're a failure!)

Sara von Tresckow

Kerstin, Likewise - I've had some patterns with odd shaft combinationsl that sink what looks to be miserably that weave just fine - and others that "balance".

The purpose of setting up a loom is to make quality fabric.

ReedGuy

Kerstin, it just happens to be by default that things balance out. I'm not fiddling around to make it so. Like anything I do, I follow a procedure. Whatever happens, happens. As I said, this does not mean their aren't adjustments. Seems that point is being over looked. No need for some to be snooty. ;)

Try to make a matching dovetail with a dull bit and unbalanced and see how it ends up. ;)

GearRat

Now, I do feel a bit silly. I was leaving the beater just hanging there when I was trying to make the shed. I didn't know that you had to push it back before throwing the shuttle. This makes things a liiiittle better, and I think I have somewhat diagnosed the problem... I am going to try lowering my treadles a bit, and lowering the beater length one spot. I have an adjustable height for my beater, and the warp, when allowed to run flat through the loom, only goes through the reed at about an inch from the bottom. That might be one of the problems... I think it is stopping the shed from getting bigger. 

Also, after the whole snapping episode, the upper levers for my second shaft are tilted when at rest. Am I guessing I need to shorten the string that goes from them to the bottom lamm? 

I am taking a bit of a break from fiddling with it tonight, since I am getting mechanic's back from laying under it to fool with the treadles, lol.  Thanks again for all of the awesome feedback! I might make a video of how it's moving so that I can make sure I've done it right. 

Sara von Tresckow

Why not also treat yourself to a copy of Laila Lundell's "Big Book of Weaving" - it deals with weaving on countermarche looms in depth, including tieup, and contains many helpful hints about weaving well. It would be the perfect comanion for your new loom.

kerstinfroberg

I'm sorry if I offended you, I didn't mean it that way. It's just that I have heard so many new-to-CM weavers despair and fiddle forever with extra treadles, or extra weights, or... just because the shafts do not stay/go back to the perfect neutral position, even if the sheds are perfect.

ReedGuy

Kerstin, all is well. I just find that it's more useful to direct someone to information or present some steps or ways to help diagnose the problem then to say something like "the purpose is to weave quality fabric". That offers nothing.

MaryMartha

Kerstin is my weaving hero. Her no-angst approach has helped my sanity more than once.  GearRat, you must be very resourceful to have gotten this far with nothing but internet links for company. 

On the subject of beater height - my Varpa's back beam is markedly higher than the front.  So I wasn't too worried that the warp rode low at the reed.  But this morning I tried raising the beater pins one notch. This brought my warp back to center and increased my shed by 3/4 in. Thanks!

How close is your fell line to the beater?  To the front beam? About equidistant works for me.  I weave from this point until just a little beyond where the beater hits the fell at 90 degrees, then advance. If I keep weaving beyond this point, my sheds get small.

Joanne mentioned differing expectations about shed size.  I should say that all my shuttles are low-profile (sometimes called damask) shuttles with cardboard quills.  Fully loaded, the whole thing is no more than 1 inch high.  Makes me rather tolerant of smaller sheds.

 

Joanne Hall

Hi MaryMartha,

Smaller sheds make the weaving go better.  Not only do you not need to press on the treadle as hard or as far, but you can also keep the tension tigher if you like. 

Joanne

GearRat

After much adjustment, swearing, readjusting, more swearing, and the assistance of some new string, I have gotten the loom up and running! I've currently got some simple scarves on there for christmas presents, and they're looking really good. The monster loom is actually quieter than my little dorothy! Thanks to everyone that gave advice! I will be putting most of the books suggested on my amazon christmas list, and hopefully people remember to check there before buying me things, lol. :) 

 

Submitted by GearRat on