Has anyone attempted, or has built a large floor loom? I'm  getting all the wood and parts together right now.I have several web sites where I can get heddles and  a reed from. Can anyone give me some info. that would help me avoid any problems? I have a louet 24" loom now but looking at the larger floor looms , they seem to be in the high price range. I have been building furniture  for over 25 years. I know someone who has a Swedish  floor loom that she said I could take measurements and pics to get the mechanics from........Steve.

Comments

Sara von Tresckow

 Make sure you get quality air dried and possibly laminated wood for your project.

The stresses on a large floor loom are beyond what most non-weavers are aware of.

You'll most likely need to get the ratchet wheels from someone who sells Scandinavian looms.

Also, when you measure that loom, have the weaver demonstrate thoroughly how everything works, perhaps allowing you to weave on that loom so you understand what you're aiming for.

Michael White

Steve, remember the measurements are going to be in metric. Like Sara said a froor loom is under a lot of stress(when my wife tightens the warp on her Macomber you sometimes can hear it shiver from the pain) buy clear wood with out any knots. I would go with birch, cherry or maple. poplar is cheap and can be had at most places like Homedepot but it is not a good wood to use as it will not hold it shape. The first floor loom I made (30 years ago) I made the ratchet wheels out of a metal blank (lots of cutting and fileing) In my older age I have gotten smarter. Buy all the metal parts from a loom company and just make the wooden pieces. Have fun and enjoy making your loom. if you have any questions IM me.

Michael

steve104c (not verified)

Thanks Sara for the good info. I will be laminating when possible. Kiln dried wood is what I'm looking at. Thanks again........Steve.

steve104c (not verified)

Michael, Thank you for the info. Clear wood is what I will be using. The Swedish loom I'm looking at is made from Scot Pine so I'm looking at clear, kiln dried yellow pine. Real close to  Scot Pine( Swedish Pine) Checking with a machine shop that has a laser cutter to make the ratchets for the warp beam and fabric beam. Thanks again.........Steve.

Sara von Tresckow

 Air dried takes longer and makes better looms - hard to find, but its the best. It is less prone to "working" later.

Since most wood is kiln dried today, those 30-40 year old Scandinavian used looms in good repair are sought after. If you can find one at a good price it might be worth the investment.

Joanne Hall

Also>

http://glimakrausa.com/used-looms.html

Joanne

steve104c (not verified)

Michael, Thanks for the web sites. Do you know how much they are asking for the Glimakra? ............Steve...

Michael White

Steve, I do not. My understanding is that they are up for bid The website is www.ocaf.com 

The Leclerc is 60" wide (Tissart Tapestry).  The Glimakra is about 39". Sorry that I was so vague.  The OCAF Thrift sale is March 12 & 13.  Check out the details on the web.  I have my doubts that we will be able to sell these quickly but if I had my choice I would keep them for OCAF.  They do not think they have a room to dedicate to weaving.  Too bad.  The homemade loom that I have in my workshop is a 36" counterbalance.  It is all there, a thing I could not tell until I put it together.  It will need some work to get it tied up properly but I have a good book to recommend.  This one will sell for about $100.  Before I dismantle it again, I will make instructions so that it can be done easily.  Bonnie

Bonnie's email is: [email protected]  if you have any questions.

Michael

Michael White

Thanks Joanne, I will add that to my list.

Michael

steve104c (not verified)

Thanks Sara,Joanne, and Michael, very much for all the info. Maybe I'll find a loom that will work for me and I won't have to build one.  I have missed 2 that were being given away. Thanks again..............Steve        fd.mann@attnet

steve104c (not verified)

Michael, Talked to Bonnie ,and my wife and I are going this weekend to pick up the Glimakra loom. Thanks a whole lot for the info. ...........Steve

Tela1

It seems all are old entries.

I am designing a countermarch loom ( 1 meter weaving width, 1.2 meters from breast beam to back beam, 8 shafts).

I would like your oppinion about breast and back beams sections. I have three possibilities in mind: 120x50 mm, 120x40 mm or 100x50 mm.

Thanks

Enrique

 

Tela1

It seems all are old entries.

I am designing a countermarch loom ( 1 meter weaving width, 1.2 meters from breast beam to back beam, 8 shafts).

I would like your oppinion about breast and back beams sections. I have three possibilities in mind: 120x50 mm, 120x40 mm or 100x50 mm.

Thanks

Enrique

 

sandra.eberhar…

If you look at the above posts, you'll see that Steve decided, after a lot of investigation into wood and metal parts, decided to buy a used loom.  You haven't mentioned how much experience you have weaving.  Many new weavers, looking at the prices of new looms, decide they would like to make one, after all, they just seem to be a big frame with warp and weft beams, right?  Actually, it is easy to make a countermarch loom that doesn't work well or at all.  The proportions in height to allow enough room to make all the parts that move up and down enough room to move has to be right or it will cause endless frustration.  Larger floor looms can be had used quite reasonably, usually for much less than the wood and parts for a home made loom.  Unless you can cast them yourself, the rachets will cost ~$250, the heddles (unless you want to hand tie heddles), will cost ~ $200.  So you're up to $450 and haven't got any wood yet.  I have bought entire rug looms for $350.

Tela1

Thanks for the answer, yes I have thought about that, to buy a used one. I think I'm risking a lot but so far it's a project on paper. I think I have the measures to make it work ... Maybe I just have fun designing a loom ...

ReedGuy

I would make it deeper to 1.5 m. And make sure your breast beam height is close to a meter high to get enough space for treadles and lamms to move. And 1.82 m tall loom frame, plus room for the jack frame on top.

I built one like a Glimakra Standard, works very well, no problem. Great sheds. Been using it 5 years now.

Tela1

Thanks ReedGuy,

Breast beam is 97 cm high (about 38"). Gallows tall is 162 cm to jacks axis (it leaves about 20 cm between shaft lower beam and upper lamms, 20 cm between upper lamms and lower lamms and 20 cm between lower lams and treadlers) (50 cm of strings between jacks and upper shaft bar - 11" heddles) (treadlers axis about 18 cm from floor) there are 50 cm -about 20 inches - between first shaft and breast beam. Do you see so critical 1.5 m to 1.2m?. Back beam is at 1.2 m but warp beam is 1.30 m. Why is so critical from 1.2 to 1.5 m?. My space is limited.

Enrique

 

 

 

 

Tela1

Thanks ReedGuy,

Breast beam is 97 cm high (about 38"). Gallows tall is 162 cm to jacks axis (it leaves about 20 cm between shaft lower beam and upper lamms, 20 cm between upper lamms and lower lamms and 20 cm between lower lams and treadlers) (50 cm of strings between jacks and upper shaft bar - 11" heddles) (treadlers axis about 18 cm from floor) there are 50 cm -about 20 inches - between first shaft and breast beam. Do you see so critical 1.5 m to 1.2m?. Back beam is at 1.2 m but warp beam is 1.30 m. Why is so critical from 1.2 to 1.5 m?. My space is limited.

Enrique

 

 

 

 

Tela1

Thanks ReedGuy,

Breast beam is 97 cm high (about 38"). Gallows tall is 162 cm to jacks axis (it leaves about 20 cm between shaft lower beam and upper lamms, 20 cm between upper lamms and lower lamms and 20 cm between lower lams and treadlers) (50 cm of strings between jacks and upper shaft bar - 11" heddles) (treadlers axis about 18 cm from floor) there are 50 cm -about 20 inches - between first shaft and breast beam. Do you see so critical 1.5 m to 1.2m?. Back beam is at 1.2 m but warp beam is 1.30 m. Why is so critical from 1.2 to 1.5 m?. My space is limited.

Enrique

 

 

 

 

Tela1

Thanks ReedGuy,

Breast beam is 97 cm high (about 38"). Gallows tall is 162 cm to jacks axis (it leaves about 20 cm between shaft lower beam and upper lamms, 20 cm between upper lamms and lower lamms and 20 cm between lower lams and treadlers) (50 cm of strings between jacks and upper shaft bar - 11" heddles) (treadlers axis about 18 cm from floor) there are 50 cm -about 20 inches - between first shaft and breast beam. Do you see so critical 1.5 m to 1.2m?. Back beam is at 1.2 m but warp beam is 1.30 m. Why is so critical from 1.2 to 1.5 m?. My space is limited.

Enrique

 

 

 

 

ReedGuy

Your distance between all levers (shafts/lamms, treadles) seem adequate and distance from shaft to breast beam is good. Breast beam height is good. As to the depth, it can benefit treadling on high tension projects, better shed, easier to get inside to tie-up. Can sit bench inside to thread heddles, if harnass is moved to the back. My heddles are 12", I had 10-1/2" ones at first but didn't like them.

You'll learn quite a bit by building your own. :)

Tela1

Fine, I am thinking in a fix location for jacks but as you suggest, to move them while threading the heddles, it is better to go to a "floating" jacks frame in order to move them backwards when needed.

I would like to make the loom as lighter as possible, what about using frame sections about 4x10 cm or 3.5x10 cm?. Or lesser?.

 

 

ReedGuy

I remove the upper lamm ties. Then, I just put a harnass craddle under the upper shaft bars and a big safety pin in the lower shaft bars. Then I move the harnass back by slinging over the back cross member.

Tela1

Thanks for sharing this.

Just inside inside the loom! No back pain!

:)

Tela1

There we go.

This is a picture of the first part of the frame assembly.

It is taking a lot of time and is not easy .

 

 

 

 

sandra.eberhar…

The deeper a loom is (distance from the breast beam to the back beam), the easier it is to form a clean shed, and the less sensitive it is to differences in tension.  If I am judging the proportions of your side frame correctly, it looks very shallow, unless you intend to add an extender to the back to hold the back beam. You have mentioned that you have space limitations; you may be happier with a table loom.

Tela1

Yes, the back beam is not in the picture. What you see in the picture is the front-breast beam, the cloth beam place - that of the big hole - and the "center" beam where the beater will hung from a cantilever. The back beam would be a folding one, any way the depth when unfolded to be 120 cm.

Tela1

Continue in Home Built Equipment Group

Submitted by Anonymous (not verified) on