My husband and I were given a Sears Fairloom in May, and have succeeded in getting it put back together (it was found in a museum, in boxes, unlabelled...). I am very slowly putting on a practice warp and have gotten through sleying (with a bent paper clip and my son holding a shop light), threading heddles (my husband cleaned them all) but now I'm stuck. The warp beam has no apron rod, just long cords with a loop attached to the beam (which has little dowels dividing it up)  so we lark-knotted the warp ends to that. But the front of the loom (we warped front-to-back) has a cloth apron with metal grommets, and a piece of rebar inside the sleeve. Seems really too heavy, and I'm stumped by the grommet placement.  I am learning all of this via a really great book and a lot of errors, but don't have anyone to ask so have come looking for aid, here. Thank you!

Comments

gailc

You can try to contact Janet Meaney at www.weaversfriend.com. She has compiled a collection of older loom manuals and has a lot of information available. I am pretty sure that I read a while ago that the Sears Fairloom is very similar to one of the Newcomb looms (Newcomb manufactured the Fairloom for Sears) and that manual could help you. For now, the back beam you describe is a sectional beam and those long cords were used to tie each section of warp, with each section tied to the cord with larks head knots, just as you described. To warp sectionally properly, though, you really need a spool rack and tension box. You can get a long enough apron rod (I used 3/8" stainless steel) and slip that through all the cords and tie onto the rod itself. You can use the same thing for the front apron rod in place of the rebar. That does seem pretty extreme. As far as the grommets - you can either lace a long cord through them, tying it at each end and slip another apron rod through the loops, or tie a cord from each grommet around the rod, making sure that all the cords are the same length. I just looked at Janet's site - there is this manual: NLC11- Instructions for Four-Harness Six-Treadle Fairloom. 4 p. The Newcomb Loom Co. manufactured the Fairloom for Sears Roebuck. It is identical to the Studio Art Loom. Also made with two harnesses. sounds like this might help.

Ryebaby

I did get a manual from Janet, and unfortunately it is not completely helpful at several critical junctures (it assumes a level of familiarity I am clearly lacking!). You are correct, the "sears" brand was just put on a Four-Harness Newcomb in the 40's. Amongst all the boxes was a tension box and a spool rack, but the warp I'm putting in is no way long enough to use the spool rack. Not to mention, my head will explode if I try to figure that out, too :) But the stainless steel rod for the front seems workable. I take it a sectional beam is different than...other ones? Thank you so much for your help so far..

 

gailc

Yes, the sectional beam is what you have - it is divided into 1 or 2 inch sections and you wind your warp one section at a time. You can, however, use your sectional beam just like a plain beam if you use the cords to hold a rod across the width of the beam, rather than use each cord to hold a section of warp. Then you can tie your warp to the rod, evenly spaced between the cords connecting the rod to the back beam. And I agree, trying to learn to warp sectionally at this point would be a head-exploding experience.

mneligh

When using a sectional beam as a regular beam, it's still much easier to warp back to front rather than vice versa.

I don't have enough space behingd or in front of my big loom to use a normal chained warp technique like I do on my smaller loom, (where I tie the warp to filled gallon jugs that drag across the floor as I reel on the warp).  When I create my threading drafts, I mark color changes as well as 2 inch sections, and measure my warp on a warping reel in 2 inch bunches.  I then crank each 2 inch section onto the beam via a tension box.

I use my hybrid approach on all warps under about 7 - 10 yards.  I drag out my spool rack for longer warps, or warps over about 7 yards that are uniformly colored.  Even using a yardage counter and electric spool winder, I find filling the spools is tedious and somewhat wasteful.  The hybrid method is easier to use in multicolor warps.  Since I do my own drafts, I tend to use a 2" modulus in the design so color changes occur on section boundaries.

sequel (not verified)

The grommetts are used to lash on a cord or rope to the actual tie on rod.  This can be another steel bar or a wooden rod.  Don't use a hobby dowel unless it is oak.  You don't want it to flex a lot.  A thinner bar may be inserted in the apron in front of the grommetts.  It's just to support the apron and grommetts.

Submitted by Ryebaby on