Greetings, I'm new here and this looks like the correct area to post this question in.  I was given an antique loom which appears from the descriptions I've seen to be a countermarch look.  The loom was largely disassembled and I am not sure how the heddles were supposed to be suspended nor how the foot pedals connect.  I've got the frame assembled and most of the large parts installed but the previous owner was in the process of modifying the heddles with a  pulley system and never finished it.  Are there any diagrams of how this type of a loom is supposed to work.  It has no makers' marks and is made of redwood so it may have been locally constructed.  The owners say it was in the family at least since the tun of the 1900s.  The loom is assembled with through tenons and pegs. Also is there aresource for threading it?

Best regards,

Charles

On the Mendocino Coast of California

Comments

Dawn McCarthy

Hi, first, can you post photos of what you have.  Secondly, I recently completed a similar renovation.  You can see pics if you go to my blog and click on the Flickr photostream in the side column.  Maybe this would be of help.  There are many weavers familiar with all kinds of looms, so ideally a photo of your loom would help identify what goes where.  My blog is bloominloom-dawnmccarthy.blogspot.com.  Also see loom restoration/renovation groups, countermarch and beyond and the counterbalance group.

 

Dawn

Slipstream (not verified)

Thank you for your response Dawn.  I've attached some photos I took of the loom.  The harnesses are sitting on the floor in front of the loom and the there are other parts are spread out around and under it.

Slipstream (not verified)

Thank you Michael, I appreciate the reference.  that is one huge and complete tome!

 

Regards,

Charles

Slipstream (not verified)

Is the loom I have possibly a smaller barn frame loom.  It appears to have all of the characteristics, pinned mortised connections, all wood, basically 4 posts.  Looks like some of the pictures i've seen of barn frame looms.

 

Regards,

Charles 

kerstinfroberg

"The big book of weaving" by Lundell/Windesjö  (ISBN 978-1-57076-392-2 or ISBN 978-1-84340-456-9 ) is the book to get for reading all about counterbalanced looms (which is what I think you have). It also describes CM looms.

Joanne Hall

Hi Charles,

Your loom appears to be made from the plans in the Worst book, Foot Power Loom Weaving, which was written in the early 1900s.  As Kerstin suggested, the Big Book of Weaving is a good one to get.  If you want tie-up information, write to me at:

[email protected]

PS  we are leaving Tuesday morning for a conference, but I can send information today if you write to me.

francorios (not verified)

Joanne, when you wrote it may be from the Worst book, I wondered how bad it could be if it is the WORST?!!

Then I found it online:
Foot Power Loom Weaving by Edward F. Worst

http://www.archive.org/details/footpowerloomwea00worsrich

It's scanned and can be read online or downloaded from the above site.

Have a good day!

debmcclintock

It also looks like you have a braking system for a bore staff...here are words explaining it, I'll try to find a picture for you to illustrate the term.  The 5 pegs on the right hand side of the loom frame are where the bore staff would be set as one advances the loom (think broom handle).  If you look at the back beam it probably has holes bored in the beam which is where you would set the "bore staff" braking mechanism.  Personally I'd switch over to a friction brake which I think has been discussed here in Weavolution.  beautiful loom!  congrats!

WeaverDave (not verified)

Wow - I want one!  :) 

I don't think it is a barn frame loom mainly because they were built into the frames of barns.  In other words, you would have to take part of the barn itself with you to get it home.

Yours reminds me of the loom shown in the book Foot Power Loom Weaving, but edward F. Worst.

Slipstream (not verified)

Thank you so much for your comments, debmcclintock.  The back beam has been modified somewhere along the line to use a set of added ratchets and a pawl.  The ratchet teeth are made individually and then screwed to the beam held b by a loose stick attached at one end to drop into the teeth.  It is an interesting way of adding ratchet teeth, each tooth has two wood screws holding it.  The system appears effective.

Regards,

Charles

Slipstream (not verified)

Between the references and the comments I have a lot to chew on for a while.  I ran across an interesting reference individually that has an interesting perspective on the history of the loom and ends with complete drawings for building a foot powered loom. The reference is called "Handloom Construction" bu Joan Kosta but Edward Worsts book is incredibly complete.  Thaks again.

 

Best regards,

Charles

Slipstream (not verified)

Hi Weaver Dave. Thank you for responding to my question, I really appreciate it. I know I am new but FWIW I did quite a bit of research before I started posting here and I found this reference to Barn-style Looms

"If you have had the opportunity to visit our Bement-Billings Farmstead museum, you might have seen a loom on display. It is sometimes referred to as a "barn-frame loom", or "barn loom" for short. The frame is constructed of posts and beams; much like the old timber framed barns. It is held together with removable wooden pegs, allowing it to be disassembled and stored when not in use." from the Bement-Billings museum page.  There numerous listings for barn looms for sale, most I suspect without the barn attached.  I have yet to see a loom built into a barn in the US although I am sure that somewhere there must be.  Joan Kosta in her book "Handloom Construction" speaks of looms that have been built into weavers homes in medeival taimes made from naturally ocurring tree parts whose morphology suggested certain parts of the loom.

Best regards,

Charles

Submitted by Anonymous (not verified) on