I made a series of photos for a friend of how I warp back to front. Some one suggested that some people here might be interested in seeing them, too.

So if you are, here they are : http://www.flickr.com/photos/dybvad/sets/72157623267479594/

Ellen

Comments

jordanj (not verified)

 Nice! This is very different from the way I warp back to front. I'm going to have try some of your techniques!

Jennifer

tracyjayn (not verified)

Thank you so much, this will really help us newbies out a lot.....

TinaHilton (not verified)

What do you use on your warp beam as you wind on?  It looks like some kind of plastic sheet.

Ellen (not verified)

Hi, Tina.

When I learned to weave I was taught to use first a round of sticks, then heavy paper.

Nowadays most weavers I know here in Denmark have switched to using a kind of plastic sheet, as you say. It is the sort people use over here to put over there trailers (tarpaulin?). It is fortified inside and very sturdy, and nice and smooth on the outside. I buy them in those big sizes that fit over a large trailer (4x6 meters) and then cut them into long lengths and the widths I want. I suppose you have something like it in the US, but I'm afraid I don't know what it is called. I hope this explanation helps, though.

It is much easier when you wind on, just get started right and you don't have to keep an eye on that beam until the piece runs out.

Ellen

 

Kristina (not verified)

 Hej Ellen,

What a wonderful idea is this pictoral tutorial!!.

I´m doing warping in the same way - . But I use always sticks  when I wind on the warp. Paper I use just to warp a Rigid heddle loom. But it`s a good  idea. I will try it  with my next warp. I sent your tutorial to my mother. She is new with weaving and this will be a great help for her. 

What kind of Loom do you have? It´s looking a little like Toika Eeva ( this is my mothers loom) or is it a Glimakra loom?

Schöne Grüße!

Kristina

Mary C (not verified)

I'm not sure if this will apply but here goes:

On my Union 36 I always warp from back to front because I can load my beam by sections from spools mounted on the back of the loom.  I don't take off my old warp from the last project but tie it off on the front and back in groups by section.  So, when I'm ready with the new warp on the beam I can just tie the new warp one by one to the old, section by section, and gently pull it through the heddles and the reed to the front. Walla, I'm ready to tie to my lease rod and adjust the tension of my new warp.

I'm doing that now, maybe I'll take a few pictures and can post them if anyone is interested:)

Mary C

Ellen (not verified)

Hi Kristina.

It makes me very happy that some people find my photo series helpful!

My loom is a Glimakra, but yes, they look quite a lot like the Toikas.It is a wonderful loom, and I am slowly saving up for another one to have in my Copenhagen home. Which would mean it has to be a smaller size, but definitely still a glimakra.

Let me know how you like the plastic sheet if you do try it, will you?

Viele Grüsse an deine Mutter auch :-)

Ellen

Ellen (not verified)

Hi Mary C,

It would be great with some photos. I like being educated here on Weavolution. Over the past 6 months I have comeacross so much that was unknown to me. Sectional beaming would be very nice to add to it. And pictures say a lot more than words, it would certainly help me understand what you have just described.

Ellen

spinningliz (not verified)

Nice demonstration Ellen. I have to learn how to warp from back to front too. I've always done it front to back which requires me to lower the back of my loom and sit on a VERY LOW stool. After getting back into weaving recently (my loom was stored for over 4 years until I had room to use it again) it was a shock to discover that it's harder for me to get up and down in that close to the floor. I didn't realize I had gotten older and my body didn't want to yield to that position anymore. It must have been quite a sight to watch my attempt...I didn't know if my bottom was going to hit the stool or the floor first. Haha!

That's a great idea to use plastic when winding the warp on. I use a roll of corrugated cardboard that takes up too much storage space and it's use per piece is too short-lived.

kerstinfroberg

A question: in photo J (finished with the raddle), it appears that you have the warp on a second rod, attached to the (hmm - I think we agreed to call it "the apron rod").
I can't see any attaching strings *in* the warp. Does that not make the warp rod curve? Or do you put them in later? - I find that my rods tend to curve, if I have the "apron strings" outside the warp width attached, so I always use only the number of apron strings that best correspond to the warp width.

I really like the plastic sheet - maybe I should go looking for some...

Ellen (not verified)

Oh, yes. I forgot to write about that. I do put the strings on inside the warp after I have finished laying the warp into the heddle, unless it is a very narrow warp. Thanks for reminding me.

I find the plastic sheets in a "byggemarked" where you get tools and equipment for house and garden and hobbies and all that sort of handyman. things. It is great to use.

Ellen (not verified)

Ha. ha. Yes I think it sounds as if it would be good for your health to find easier ways of dressing your loom :-0

You are welcome to ask me if there are things I haven't explained well enough.

Mary C (not verified)

Hi Ellen,

I uploaded a few pictures to Snapfish (similar to photo bucket).  This link should get you there.

http://www1.snapfish.com/thumbnailshare/AlbumID=2114180016/a=145686458_145686458/otsc=SHR/otsi=SALBlink/COBRAND_NAME=snapfish/

Hope this is useful:)

Su Butler

HI Ellen.....if you want to see a comprehensive video on sectional beaming, take a look at the LeClerc website...

http://www.leclerclooms.com/ind_eng.htm

Scroll down to the second video on the page called Sectional Beaming.

Su :-)

Ellen (not verified)

Hi Mary

Thank you very much. I could only get to see the first photo, though, or else had to join yet another photo-sharing site, and joining flikr was enough for me. All these accounts with id-names and passwords and stuff, I try to keep it to a minimum.

Ellen

Ellen (not verified)

Hi Su,

Thank you, that was very instructive. It seems to me that it takes a lot of extra work and complicated equipment to do that. But I suppose it is because I am only an amateur, there must be advantages in it for professional people, I guess.

But as I said, I really like all the learning that is possible here.

Ellen

Submitted by Anonymous (not verified) on