I wound up a warp for a quick, but long, scarf the other day and, as promised, here are the photos. Please feel free to ask any questions. This is how I learned to do it on a warping board. That doesn't mean it's the only or the right way to wind a warp.
I used the warping board on the back of my Kromski Harp and placed it on the Kromski stand.

I first determined the path the warp would take to achieve the length i wanted. In this case, it was 2.25 yards.

I started at the peg at the bottom right (just out of sight) and made a cross at the top and then turned on the top right peg and followed the path back down to the bottom.


Here are two pictures where you can see the cross at the top. See how the yarn stays in the order it was wound. It's a good way to keep the warp from getting tangled. It's important to maintain that cross, makes threading much easier.


As I wound, I kept track of the number of threads by using a thread tied every 10th thread since my heddle is a 10 dent heddle. When I finished winding the warp, I tied everything very securely, especially the cross.
I learned to put an extra tie right at the cross as well as ties on either side of the cross just to be certain it held in place.

I place ties at each end and sometimes use different color ties for the top and bottom of the cross so I can be certain not to twist it.


Then I chain it to remove it from the board. It's like crocheting with your hand.
The finished chain.
That's it for winding the warp. You can choose to chain it or just carry it from the warping board to the loom. In my case, the warping board is on the back of the loom so I chain my warp, remove the pegs, flip the loom over and then begin the threading process.
THREADING THE HEDDLE
Leave all the ties on while you get it set up. First step in threading is to secure the warp to the front of the loom like this:
Wrap it around the front beam making certain it is long enough to reach past the rigid heddle which is seated in the neutral position in the heddle block.
Next, hold the warp on your left hand (I like to thread with my right hand, do it the other way around if you are left handed) with the main part of your hand in the top loop above the cross and your thumb below the cross like this:
Then, remove the ties around the cross and start threading through the heddle and on to the back apron rod. The Kromski loom has a "warp helper" that holds the apron rod into the side of the loom. I was able to mimic this feature with my Beka loom using small bungee cords. These pictures show the Kromski version so you can see how it works.
Take the threads out of the cross, one at a time, bring them through the slot and onto the apron rod.
Once all the threads are through the slots ONLY, check to be certain you have threaded through every slot, measure the width in the reed to be sure it is the width you had planned (about 10-15% wider than the finished article to allow for draw-in and shrinkage)
Finally, untie the warp from the front beam and hold with firm tension while winding the warp onto the back beam. You may need to enlist another pair of hands or use weights or plastic milk jugs filled with water to maintain even tension on the warp as you wind it onto the back beam. Keep the warp threads separate as they are wound on by using 12-15" length pieces of brown craft paper or paper bags. Make sure the paper/bags are wider than the warp.
Once the warp is wound firmly onto the back beam and is hanging past the front of the heddle by about 24", I cut the warp threads in front, remove one thread from the slot and bring it through the hole. This way you have one thread in the slot, one in the hole across the entire heddle. Tie them loosely in groups of 10 or about 1" as you thread so remain securely in the heddle.
Next, remove the tie holding each group and tie each 1" group onto the front apron rod making certain the tension is even on each group and begin weaving with some junk weft yarn to spread the warp and create space for fringe or hemming. Now is the time to do a hemstitch on the front end of the project if that is your desired method for securing the weft.
Happy weaving,
Claudia
Comments