TheLoominary (not verified)

Hello, the "cardboard" spools you see on the rack that I built are actually quite sturdy.The material is more like a press-board than a cardboard.They should last for years if used carefully. They were purchased at Halcyon Yarn (on-line) for $ 1.25 each. Very strong ones made of styrene plastic are available on-line at Leclerc looms, however they cost a whopping $ 3.75 each! Another option is available at cheeptrims.com, as they have cardboard spools 4" long with 8" ends that be trimmed to the customary 3" ends for $.52 each, sold in a bag of 25.They are lighter than the others, but the price is good. You will need a spool winder to load your spools. A fellow on e-bay is building a nice one for around $150.If you would like to build your own you can also purchase a new sewing machine motor/with foot pedal at e-bay, however the one for $150 is a good price. Go to the Leclerc looms site, and you can see a video showing their winder being loaded. Hope this has helped, Frank

TheLoominary (not verified)

Hi ReedGuy. Great job on your rack. I like the fact your dowels "snap" into place. My rack is used for sectional warping, so it goes directly to my tension box, then to my sectional beam. Here is a photo of a vintage German spool I have. It measures about 7"w x 8" h. It is +- 90 years old, and made of Beech and Spruce, as are many German weaving items. Should you build your wood spools, please show us a photo, there also seems to be some interest from others to also do them.Thanks, Frank

Claudia Segal (not verified)

I would use the chart provided by Lillian Whipple in the article HERE.  I imagine each square could also be a bead.

Lillian is also teaching a class on this subject, Summer & Winter and Taquete on Cyber-Fiber which is HERE.  You can join a FREE Open House and see how it works.

Claudia (Segal, not Chase), Weavo co-founder

TheLoominary (not verified)

Have you been fighting your equipment? Do you have an Idea how to to make it work better? Some weaving equipment designs have been around for what seems like an eternity! What we are using today is the result of trial end error,innovation,and improvements made by weavers just like us! You don't need a PHD in wood working, or metal fabrication to make improvements.Most of the equipment I build is done outside in front of the barn with hand tools,and light duty power tools.The hard work comes from the studio,taking notes,making drawings,writing down Ideas before I forget them!Lets change it,fix it and get back to what we all love WEAVING! Regards,TheLoominary

steve104c (not verified)

Came across a great deal. I have a Delta Contractors saw 1988 model ( I bought new). Where my wife works, they have a "for sale" bulletin board on the computer. She called me the last Thur. and said someone was selling a Delta Contractors saw,  year 2002 model. The last year this model was made in USA. Saw w/30' Unifence and table, portable stand, dado blade and three other blades. $500.00. Cleaned it up. He had stored it in the garage for last 4 years and I would guess he hadn't used it more than a dozen times. Looks brand new. Going to give my old saw to my nephew.............Steve.

TheLoominary (not verified)

Ah!, a new saw, maybe a new equipment project to test it out on! A quality tool that will aid in turning an idea into a new weaving tool! Enjoy, Frank.

TheLoominary (not verified)

Hello Kerstin, First, let me commend you on your very artful use of "found" items such as the fork. I know of one Swedish company manufacturing very high quality hole saws. Sandvik is well known world wide. The saw cups have holes in the side of the body to insert a pin, or screwdriver to aid in material removal. The "Bi-Metal" type would be a good choice for longer wear.I don't know how fine the tooth count is available in their product line however. That said, a little trick to aid in wood grain tear out,would be to place "masking" tape around the area to be cut, both sides,then remove, pulling carefully from the inside toward the cut edge.Hope this helps. Frank. 

TheLoominary (not verified)

Hello Kirstin, I have experienced similar problems with hole saws. The enemy of all tempered cutting surfaces is HEAT! This is a greater problem when using the cheaper saws. I have found that making small cuts, then backing off to keep things cool will extend your tool life. Also, I use a round screwdriver with the tip wrapped with tape as a cushion just large enough to pass through the hole. If you have two holes switch back and fourth prying evenly.If your tool has a set screw to hold the drill bit, loosen it while removing your circle. Hope some of this helps.Frank.

Slipstream (not verified)

I don't know how many of these you make at a time and I am not sure what the diameter or the thickness of the disks is but most hole saws I use (my favorites are Lennox and Milwaukee but Sandvik makes excellent saws)  have a couple of holes in the back and the mandrel unscrews from the saw body so you can pull out your center drill.  You could make a disk that fits loosely in the hole saw with two projecting dowels (metal) that project through the two holes in the back of the saw.  Remove the mandrel and center drill, tip the saw over and hit it on a flat surface to dislodge the disk.  The disk on the inside fo the say wojld not mark the disk you cut provided you did not have anythin projecting on its face. If you felt uncomfortable with two spinning dowels you could always have two dowels set in a piece of wood that went through the back of the saw and pushed on the loose second disk inside thereby preventing the work piece from being marked.

 

Regards,

Charles

TheLoominary (not verified)

Hello Cashrut, building a Winding Station is a great way to organize, and as you said, it is a straightforward design.The spool rack/ twining station I built, pictured on the front page of "Home Built Equipment" was built of 1"x4" #2 pine scraps, and the spool rack of poplar, purchased locally at "Home Depot". While most commercial equipment is built of Maple or other hardwood, pine will last for many years of use. There are good photo's ,and measurements at: Halcyon Yarn, Paradise Fibers, and Camilla Vally website's of the items you want to build.I use a "roundover" bit on my router on all edges to assure smooth edges, but a good hand sanding will also work well.I personally like the base of the Schacht Winding station, as it is wide and stable, that said, the Leclerc unit could easily be done the same way. Hope this helps, and perhaps someone else has one of these units, and will post more detailed measurements. Regards, Frank