ruthmacgregor (not verified)

Sure, Laverne.  This is a picture of my semi-rigid heddle in action:

I make these myself (and sell them), and though this narrow one is the only width I sell right now (excellent for warp-faced bands, not wide enough to be interesting for anything else), I'm prototyping a wider version with a closer sett -- for use in weaving things other than bands.  It's fiddly to make a heddle using TexSolv for the "business" part, but they're really nice to use.

I have two rigid heddles that I made using rigid heddle sections like the ones you found at Village Spinning & Weaving -- sections joined with wooden channels.  They came into existence a few years ago, when I wanted three matching heddles for my RH loom (which is an odd size and was no longer being manufactured).  Those are actually in use right now -- but I'll take a photo and post it in just a bit.

Photo forthcoming....

Ruth

ruthmacgregor (not verified)

Okay, here we go -- the heddle being lifted in the photo was made from purchased rigid heddle segments (each about 4 inches wide), glued into place in wooden channels, top and bottom:

You can see some funny spaces between the segments where I didn't quite get things lined up correctly -- but those don't affect the weaving at all.

The wooden "channel" pieces were sticks of wood with a square cross-section and a deep groove running down one side.  To make the heddle, you just put glue in the channel, then slip the heddle segments into place and squish it all together firmly.

If you didn't have any wooden channels, you could just use a stiff(ish), sturdy tape to connect the tops and bottoms of the segments together.  A couple of layers of duct tape would work nicely.  ...It's not as pleasant to touch as wood, but functionally there'd be nothing wrong with it.

I was looking around online for UK suppliers who might sell heddle sections, but without success.  The ready-made rigid heddles are available just about everywhere, though -- and they're a lot less expensive than they used to be, back when I made these heddles.  If you want some supplier names, just send me a message and I'll tell you everything I know. :-)

Ruth

weave2 (not verified)

 I was reading through some Hamdwoven magazines from the 1990's and in one is a homemade rigid heddle loom instruction.  I was going to let Laverne know about in case she may want to give it a go.  The issue is Jan/Feb 1996.

It looks similar to the 'baby loom' that someone has posted on the site recently.

Alaa

tobytottle (not verified)

Thanks for all the photos and advice everyone! Ruth and I were able to meet up at The Handweaver's Studio in London yesterday, which was fantastic! I've never been surrounded by such a range of yarns, equipment and good advice/experience before! It was inspiring. I was tempted to buy one or two of the rigid heddle sections they have there, but I think for now I'll perservere with improving my technique for opening string heddle sheds - and using easier, smoother yarns won't hurt!

Bobbie2 (not verified)

Ruth, whethe re do I find info for buying your heddles? Also, if buying the ones mentioned here from Village, what size would you suggest. As you probably can tell, I am new at this and just learning.  Using the rigid heddles is just another method instead of making your loops, correct?

rose Goldielocks (not verified)

I purchace 12" wooden dowels, or 'square' dowels... (the square dowels are found in the 'woodworking' section of michaels and JoAnn's near the round wooden wheels and popcycle sticks)... If I want a longer segment, Home depot and lowes have them up to 48" long. Generally, the wooden dowels under 1" in diameter or square section are priced under 5$ each. then I take a 'zip tie' or little plastic tie that is used to keep electirical wires together and tie the sections of the Rigid heddle to the dowels. I have had success using normal string to do the tyeing also. I go though the slots on the edges of the heddle segment, and it does not interfere with weaving, and if I want to re-arrange the segements, I simply cut the ties and re-arange away!

ruthmacgregor (not verified)

Yes, rigid heddles take on the job of lifting (or lowering) warp threads -- so in a backstrap setup they perform the same function as the string-loop heddles.  There are many paths leading to the same place, as is so often the case....  It's worth trying everything, though.  That way you gain experience, and you can choose to pursue the path you like the best!

As for choosing the size of the plastic rigid heddle sections -- you're basically choosing the number of threads per inch allowed by the heddle.  When you're weaving a warp-faced textile (as we're mostly doing with the backstrap), those numbers mean less than when you're weaving fabric where the weft will show.  On a practical basis, for warp-faced weaving, a wider spacing (say, 8 or 10 epi) will give your warp threads extra space to move -- useful if you want to weave with fuzzy yarns.  A closer spacing (say, 12 epi) will let you use a larger number of warp threads in a given space -- which gives you more room for patterning.

With regard to my little semi-rigid heddles, you can find them by clicking on my profile and following the link to my website (sorry to be obtuse, but we're non-commercial here in Weavo, and that's a good thing!).

The busy travel season here has come to an end, so I'll be able to catch my breath and actually do some weaving again (yayyy!!).  I haven't had the chance to check in here much since meeting Toby in London.  (Toby, have you had the time to try out those beautiful cottons you found?)

Ruth

Bobbie2 (not verified)

I didn't even think about that when I asked. :(

ruthmacgregor (not verified)

Oh, heavens, don't worry about it, Bobbie!  Actually, I thought it was lovely that you were interested! :-)  I'm just careful about that stuff, if you know what I mean.

Looking back, I see that I didn't completely answer your question about the plastic rigid heddle sections -- I talked about thread spacing, but not the width of the heddle sections themselves.  If you look at the descriptions from The Village, you'll see that the 10 dpi sections (dpi = dents per inch, in other words the number of threads you can thread per inch) are about 2.5 inches wide.  That means that for each section, you'll be able to thread no more than 25 warp threads.  That's not a whole lot, as you already know!  For that reason, if you decide to weave with the rigid heddle sections, you'll probably want to purchase several of them rather than just one.  ...Sorry I didn't make that clear the first time around!

We're settling in for winter here -- good weaving weather, and I'm looking forward to it!

Ruth

Claudia Segal (not verified)

Hi Ruth and Bobbie,

It's just fine to talk about and give the link for your shop.  We enjoy seeing the wonderful ways weavers are supporting other weavers and making a little money, too.  The only thing I ask is that when you post a link, please set it to open in a new window by going to the second field in the link window and clicking on "open in new window".  The help topic showing how to do this with diagrams, etc. is HERE.

BTW, Ruth your heddles are very clever and I am very tempted once I get going with my backstrap weaving.  Thanks for sharing.

Claudia, Weavolution co-founder