tien (not verified)

Hi Deb,

Tension loosening: I just wrap the beginning and end threads two or three times around the clip at the start and end of each bout.  That holds them tight enough for me. 

I had some trouble with the beginning thread going slack on me, but eventually figured out that it was because I needed to push back each winding's worth of thread to the back edge of the warping wheel "bobbins" before going down to the clip and back again.  I had been winding, going to the clip and then back out to the crossmaker, and THEN pushing the freshly wound thread to the  back - this resulted in loose threads because I was pushing the freshly wound section back about an inch or so, and of course that loosened up the thread that was crossing the section on its way down to the clip.

The last thing I've discovered is that the first and last threads frequently go slack on me simply because they are winding onto the beam unevenly.  I had been winding only 1" wide in the "comb", which turned out to be a mistake because the bout narrows a little between the comb and the beam.  I now wind about 2-3" wide in the comb and turn the angle until I have something almost exactly 1" wide, winding onto the beam.  But even so I find it quite fussy to get the edges exactly right.  Especially on my Workshop Dobby Loom, with its small beam, I sometimes have to stop and wind a few yards back onto the warping wheel, adjust the angle/location of the wheel, and restart the winding.

Another thought: how are you pushing on the threads as you wind?  I always push each freshly-wound length of yarn back  as far as it will easily go before winding the next bout.  This keeps the threads more or less lined up.  If your first threads are getting buried under subsequent windings, they will be under more tension as they reel off and so will wind up being slack at the end.

That's all I can think of for now...

Tien

tien (not verified)

One thing you might consider on the WDL is enlarging the warp beam.  The small diameter makes it really hard to wind on evenly, especially at first, and that teeny-tiny little groove doesn't accommodate knots very well.  I wrote a blog post on how I enlarged my warp beam here: http://www.tienchiu.com/2008/09/upgraded-my-sectional-beam/ .  It's made a huge difference in my warping.

When threads start going slack on you, look at the section that's been wound on to see if it is "falling off" at the edges.  If it is you'll have to wind a few yards back onto the wheel, nudge the wheel so it's a tiny bit closer to the problematic edge, and start winding again.  In a fit of desperation I've been known to take the entire bout and wind it around the problematic edge for a turn or so to "build it back up", but that's really a desperation move; if you catch the slackness early on, you should be able to fix it just by nudging the wheel.

One last thing I do is hold my finger so the warp just barely touches it as it's winding on.  This lets me feel quickly whether the tension is going slack on one end - you don't want the warp running firmly over the finger as that will disrupt the tension, but if it's just barely touching it shouldn't disturb anything.  But on my last few bouts I tried just keeping an eagle eye on the bout as it wound on, and caught some early tension problems without having to "feel" them.

The WDL is definitely tricky to use - I had serious difficulty with mine at first and wouldn't recommend it for a beginner - but most of the issues have to do with its size.  Small looms give you much less "wiggle room" for minor errors, so you really do have to be meticulous about technique to get it to work.

That said, I love mine - where else are you going to get 24 shafts in such a small package???

lkautio (not verified)

Finger laces (the many forms of leno, Brook's Bouquet, Tarascan, etc.), embroidery weaves, clasped weft, clasped warp, beaded wefts, tapestry, etc. 

http://www.indianaweavers.org/weavingIndiana/EleanorBest/LaceByHand.pdf

Virginia West, Finishing Touches for the Handweaver

Jeanetta Jones, Embroidery Weave Workshop (book)

Nancy Harvey, Tapestry Weaving

Betty Davenport, Textures and Patterns for the Rigid Heddle Loom

Laurie Autio


jenadina (not verified)

I'd love to do a series based on the Textures and Patterns book, but I've got Christmas gifts to weave (don't know anyone who would use mug rugs) so I won't be joining in this time.

jeannine (not verified)

hi to all,

I couldn't  stand it no longer to sit around doing nothing. So i took my little frame loom and put a continuous warp on it. It is in pure Saori -style  ,totaly without any  planning and is intended to be 4 mug rugs. I use some leftover novelty yarn and I am weaving weftreb.I wonder how it will turn out in the end but i am happy to be weaving again.

I am also testing some new yarn(rope)for stringheddles .It is nylon(yah I know) only 0,5 mm ,from diy-shop (used when putting floortiles in)I will see how it behaves and if the knots stay in place.

 

jeannine (not verified)

the main weft is a strand of  60thin gray and black acrylic yarns( I have lots of thin yarn must make combinations) ;the other is black with lurex ;the red is eyelash yarn with a litlle red lurex .you can see it in this picture.

 

 

Aunt Janet (not verified)

Cool mug rugs Jeannine.  I looked at your flickr photos, too.  I like the bits of color in your rugs.  they look casual and spontaneous.  

 

Caroline (not verified)

Love the mugs, and loved your other photos - you must have had fun experimenting - and mug rugs are ideal for that! I hope you realise that this gets contagious!!!! I already have projects about to become to take form, and there you are wickedly suggesting another fun thing I could be doing, hehe! But I can't have an empty loom can I?

jeannine (not verified)

thank you all for the nice reactions:)

I know it gets contagious and I struggle to limit the amount of project i have going .I also am tempted by the rosepathwal but i have put that on hold because for the moment i am still limited to the frame loom. next project is a test of my homespun yarn.

jeannine